Products

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Washer Reservoir Cap for the windscreen washer fluid reservoir. Seals the filler neck of the washer bottle in the wash/wipe system, retaining wash...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

Auxiliary Water Pump - an electrically driven coolant pump within the engine cooling system. Unlike the main belt-driven pump, it circulates coolan...

Timing Chain Tensioner for the timing chain drive of the 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. It bears against the timing chain...

Air Suspension Compressor The pump that generates and supplies compressed air to the four-corner electronic air suspension system. Driven by an el...

Water Pump for the engine cooling circuit, fitted to supercharged petrol applications (3.0L DOHC GDI supercharged V6 and 5.0L AJ133 DOHC supercharg...

O-Ring - seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200 diesel engine, it maintains a lea...

Hex Head Bolt - M14 x 148mm fastener used at the front crossmember and stabiliser bar, front suspension arm, rear bumper and tow bar mountings. A ...

Oil Pump for the engine lubrication system of the supercharged petrol V6 and V8 (AJ133) engines. Driven from the crankshaft, the oil pump draws oi...

Transmission Mount Insulator locating the transmission mounting bracket. The rubber-to-metal insulator supports the transmission against the body ...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Exhaust Gas Pressure Sensor for the exhaust and emissions system on 2.0L AJ200P Ingenium petrol and plug-in hybrid applications. The sensor measur...

Head Gasket for the right-hand cylinder bank of the 5.0L V8 AJ133 petrol engine. It seals the cylinder head to the engine block, containing combust...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Cover Gasket for the crankcase cover, part of the emission-control and crankcase ventilation system on the 2.0L AJ200 four-cylinder diesel engine. ...

Engine Mounting Bracket - a structural bracket within the engine mounting system. The bracket bolts to the engine and locates the engine mount, ca...

Thermostat for the 2.0L Ingenium diesel engine (AJ200D) cooling system. It regulates coolant flow to bring the engine up to operating temperature q...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Fuel Pressure and Temperature Sensor for petrol fuel-injection systems. The combined sensor measures fuel rail pressure and fuel temperature and r...

Front Cylinder Cover - a cover that closes off the front face of the cylinder block, sealing the opening and enclosing the components behind it. F...

Combined Oil and Vacuum Pump for the 2.0L Ingenium (AJ200) diesel engine. This tandem unit houses the engine oil pump and the vacuum pump in a sing...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Clip for exterior body trim and accessory fittings. The clip retains body mouldings, side steps, mudflaps and related exterior trim to the body, p...

Exhaust Gas Pressure Sensor for the 2.0L AJ200D Ingenium four-cylinder diesel, working within the turbocharger and exhaust gas management circuit. ...

Cooling Fan Motor in the engine cooling system, driving the radiator cooling fan. The motor spins the fan to draw air through the radiator, dissip...

Camshaft Cover for the 5.0L V8 AJ133 supercharged petrol engine. It closes the top of the cylinder head, enclosing the overhead camshafts and valve...

Cylinder Head Cover (Camshaft Cover) for the 5.0L V8 AJ133 petrol engine, naturally aspirated and supercharged applications. The cover bolts to th...

Crankshaft Pulley with integral torsional vibration damper, mounted on the crankshaft nose of the 2.0L Ingenium AJ200 four-cylinder petrol and dies...

Tensioner Pulley for the auxiliary (accessory) belt drive on 2.0L AJ200 / AJ20 Ingenium petrol and diesel applications. The spring-loaded tensione...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

EGR Inlet Gasket for the exhaust gas recirculation circuit of the 2.0L I4 AJ200 Ingenium diesel engine. The gasket seals the EGR inlet joint on th...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Timing Gear Special Nut from the front timing gear assembly, securing the lower primary timing chain guide. The nut locates and clamps the guide a...