Products

Upgrade your Land Rover Defender or Series vehicle with this complete 73mm LED Light Upgrade Kit. Designed to replace traditional incandescent lamp...

Headlamp Assembly - a complete halogen headlamp unit for the front lighting. Supplied with the right-hand-drive beam pattern, and without the wiri...

Fuel Cut-Off Switch Fuel stop solenoid switch mounted on the diesel injection pump, controlling fuel flow into the pump's metering circuit. When d...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Alternator Bearing for the vehicle charging system. This bearing supports the alternator rotor shaft, allowing it to spin freely within the altern...

Shim hinge

Voltage Regulator (control box) of the screw-terminal type, for dynamo charging systems. The control box is wired between the dynamo and the batte...

Bracket

Door Check Arm Bracket - the bracket that carries the check strap channel for the rear side door. The door check arm runs through this bracket to ...

Check Assembly Door Rear - RH

Rear door check assy LH

Inner Door Panel Assembly - the inner skin of the rear side door shell. The inner panel forms the structural inner face of the door, carrying the ...

Inner Door Panel Assembly forms the inner structural panel of the door. This panel makes up the inner face of the door, providing the mounting str...

Door Check Arm Bracket anchors the rear side door check strap to the door assembly. The check strap limits how far the door swings open and holds ...

Bracket

set screw M6 x 25mm 8.8 various applications

Bolt - M6 x 55mm hex head bolt used in braking system assemblies. Standard metric hex fastener supplying clamping force in brake-related mounting ...

Bolt - M6 metric thread, 70 mm long. A threaded fastener for securing components at a bolted joint. Tightened to the torque specified for the asse...

Bolt Threaded fastener used within the exhaust system assembly.

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Panhard Rod Bolt - a metric hexagon-head bolt measuring M14 x 80mm, used to secure the Panhard rod within the axle location. The Panhard rod locat...

Bolt - M16 x 90mm is a hexagon head bolt used in the front suspension assembly of Land Rover vehicles. Fits the radius arm mounting, securing the ...

Bolt for the engine front cover. Hexagon-head threaded fastener securing the timing front cover on the V8 petrol engine. Supplied individually.

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

High-Tensile Hexagon-Head Bolt - an imperial 7/16" UNF fixing bolt, 2-1/2" long, in high-tensile grade. A general-purpose hex-head fastener with a...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Radius Arm Bolt with a 5/8" UNF (Unified National Fine) imperial thread and a 3-1/2" shank length. Secures the front radius arm to its axle or cha...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Door Check Strap - Front, Left-Hand (LH), Flat Type is the front door check strap (door checker), part of the door assembly. It links the door to ...

Tailgate Bracket for the rear tailgate. This bracket mounts to the rear body and supports the tailgate, providing a fixing point on High Capacity ...

Bonnet for the Defender Puma era body assembly. This bonnet is taller and wider than the pre-2007 Defender bonnet, with a distinctive raised centr...

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

LED Light Kit - 73mm

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Rivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...