Products

Brake Pad Fitting Kit - Front - caliper hardware set used when renewing the front brake pads, covering the guide bush and seal components that loca...

Front Exhaust Gasket for the 3.0L V6 diesel engine, sealing the joint between the exhaust manifold and the front downpipe. The gasket maintains a ...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Overflow Container Cap for the cooling system expansion (overflow) reservoir. The cap seals the coolant expansion tank and maintains system pressu...

Fuel Injection Kit - 3.0 V6 Diesel is the cylinder 1 injector refit kit for the 3.0L V6 diesel fuel injection system. This kit supplies the compon...

Fuel Injector Kit - injector refit kit for the 3.0L TDV6 diesel engine, supplying the sealing and clamping components required when a fuel injector...

Injector Refit Kit - Cylinders No.3 and No.4 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and...

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...

EGR Valve for the left-hand cylinder bank, part of the exhaust gas recirculation system on the 3.0L V6 24V DOHC turbo diesel engine. The valve met...

EGR Valve Assembly for the left-hand cylinder bank of the 3.0L V6 24V DOHC turbo diesel engine, supplied as an assembly with its EGR cooler. The e...

EGR Valve and Gasket for the right-hand cylinder bank, part of the exhaust gas recirculation system on the 3.0L V6 24V DOHC turbo diesel engine. Su...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Immobiliser Transceiver for the vehicle anti-theft (immobiliser) system. This is the transceiver aerial that reads the transponder in the key at t...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

EGR Inlet Gasket for the exhaust gas recirculation system on the 3.0L V6 turbo diesel engine. Seals the joint at the EGR inlet, where recirculated...

Sensor Assembly

Sensor Assembly

Injector O-Ring is the lower sealing ring for a diesel fuel injector, used on 3.0L SDV6 and 4.4L TDV8 engines. It seals the lower body of the inje...

Automatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...

Automatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Parking Sensor is a Park Distance Control (PDC) ultrasonic sensor mounted in the bumper, part of the parking aid system. It emits and receives ult...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Injection Pump Leak-Off Tube for the 3.0L V6 diesel engine. It carries leak-off (return) fuel from the high-pressure injection pump back to the fu...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Self-Tapping Screw and Washer - a 5 x 20mm self-tapping screw with a captive washer, used as a bumper and grille fixing. It secures the radiator g...

Rear Anti-Roll Bar Bush - locates the rear anti-roll bar (stabiliser bar) to the chassis. The bush clamps around the anti-roll bar where it mounts...

Ride Height Sensor - electronic air suspension height sensor. The sensor links the suspension arm to the body and continuously reports the ride he...

Ride Height Sensor - rear electronic air suspension height sensor. The sensor links the rear suspension arm to the body and continuously reports t...

Bolt - front brake caliper mounting bolt. The bolt secures the front brake caliper to the hub carrier, clamping the caliper against its mounting f...

Brake Pad Wear Warning Wire for the rear brake pad wear-indication circuit. The sensor wire is routed into the friction material of the rear brake...

Brake Pad Wear Warning Wire for the rear brake pad wear-indication circuit. The sensor wire is routed into the friction material of the rear brake...

Brake Pad Wear Warning Wire for the rear brake pad wear-indication circuit. The sensor wire is routed into the friction material of the rear brake...

Brake Disc is a rear vented brake disc, part of the rear braking system. It provides the friction surface the rear brake pads clamp against; inter...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...