Products

Blade Fuse - 5A is a 5-amp plug-in automotive blade fuse used in the vehicle fuse and relay boxes to protect an electrical circuit. It seats in a ...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Exhaust Pipe Gasket seals the joint in the front section of the exhaust system, maintaining a gas-tight connection between the mating exhaust flang...

Water Pump circulates coolant through the engine cooling system. Driven from the engine, it pumps coolant through the block, cylinder head and rad...

Gasket - Exhaust Manifold

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Ignition Coil

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Brake Pad Set for the front axle, sized for 18-inch brakes. The set provides the friction material that acts against the front brake discs. It is ...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Brake Pad Wear Wire is the rear brake pad wear warning sensor, fitted to the rear brake pads within the rear disc and caliper assembly. The wire c...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Solenoid Control Switch - ignition and start control switch located in the facia and console. It controls the engine start function through the ve...

Radiator Top Hose for the engine cooling system of the 2.0L TIVCT turbocharged petrol engine. Carries heated coolant from the engine outlet to the...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Sealing Ring - 34.2 x 3.0mm O-ring that seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200/AJ...

Engine Cooling Fan Motor

Front Suspension Arm for the front suspension. Locates the front wheel hub carrier and controls its movement through the suspension travel.

Thermostat regulates coolant flow within the engine cooling circuit. It stays closed while the engine is cold to speed warm-up, then opens at its r...

Brake Caliper is the rear brake caliper within the rear disc brake assembly. It houses the hydraulic piston and carries the brake pads; under brak...

Brake Caliper is the rear brake caliper within the rear disc brake assembly. It houses the hydraulic piston and carries the brake pads; under brak...

Front Brake Pad Wear Sensor for the front axle brake assembly, forming part of the brake pad wear warning circuit. The sensor is a wire loop carri...

Engine Oil Pan - the sump casing that closes the bottom of the cylinder block on the 2.2L 16V common-rail diesel (DW12) and forms the engine's oil ...

Cabin Pollen Filter, 272x195x43mm - the filter element in the HVAC intake housing, installed upstream of the blower motor and evaporator. All air ...

Inlet valve stem seal for the cylinder head valve train. The seal is pressed onto the inlet valve guide boss and wipes the valve stem as it recipr...

Front Brake Pad Wear Sensor Wire from the front brake pad wear warning circuit. The sensor wire is routed into a slot in the front brake pad frict...

Hub Bearing

Front Wheel Arch Moulding for the right-hand side, part of the exterior body cladding assembly. The moulding follows the flange of the front wing ...

Front Wheel Arch Moulding for the left-hand side, part of the exterior body cladding assembly. The moulding follows the flange of the front wing w...

Transmission Sleeve Kit

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Rear Wheel Arch Moulding - exterior body moulding that follows the line of the rear wheel arch, part of the exterior mouldings and cladding group. ...

Front Brake Hose - the flexible section of the front brake circuit, running between the rigid brake pipe on the body and the front brake caliper. T...

Front Brake Hose for the left-hand side - the flexible section of the front brake hydraulic line that connects the rigid brake pipe on the body to ...

Relay - 20 A five-pin micro relay, black housing. A five-pin relay is a changeover type: a low-current control circuit energises the coil, which s...