Products

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Air Suspension Compressor Mounting - rubber isolator supporting the electronic air suspension compressor at its rear mounting point. The compresso...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Brake disc rear

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Filter Kit groups the consumable filters and ignition parts required for a scheduled service of the 4.0L and 4.6L V8 petrol engines. The kit conta...

Service Kit for the 4.0L and 4.6L V8 petrol engines, covering the scheduled lubrication, induction, fuel filtration, ignition and cabin air items i...

Service Kit for the 2.5L six-cylinder BMW M51 turbo diesel, covering the scheduled lubrication, induction, fuel filtration and cabin air items in a...

Service Kit for the 2.5L six-cylinder BMW M51 turbo diesel, covering the scheduled lubrication, induction, fuel filtration and cabin air items in a...

Service Kit for the 2.5-litre BMW M51 six-cylinder turbo diesel, gathering the replaceable filters required for a scheduled service into a single k...

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Kit diff wh OEM NLA AFTER STOCK ENDS

O-Ring for the battery compartment lid of the Range Rover P38 remote key fob. This small rubber seal sits in the groove around the battery cover, ...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Brake Caliper for the rear braking assembly, mounted on the right-hand side. The caliper houses the piston and hydraulic fluid inlet, converting p...

Rear Brake Caliper Carrier for the rear disc brake assembly. The carrier bolts to the rear hub and holds the brake pads, locating the caliper over ...

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Rear Brake Caliper Seal Kit for rebuilding both rear brake calipers on the Discovery 2 and Range Rover P38, supplied as a pair to cover both sides ...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Front Brake Caliper Slider Pin Dust Cover Kit. This kit supplies the rubber boots that protect the front brake caliper guide pins (slide pins) fro...

Brake Caliper - front left-hand caliper in the front disc brake assembly. Under hydraulic pressure from the brake circuit, its pistons clamp the b...

Front Brake Caliper for the right-hand side. The caliper straddles the front brake disc and houses the hydraulic pistons that force the brake pads ...

Carrier for front calipers, fits both LH + RH

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...

Discovery 2 en Range Rover P38: revisieset remklauwen voorzijde.

Front Brake Caliper Guide Pin Set for the front disc brake calipers. The guide pins let the sliding caliper float on its carrier, so the caliper ca...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Steering Universal Joint for the lower steering shaft. This joint connects the lower steering shaft to the steering box input, transmitting steeri...

O-Ring seals the drive belt tensioner fulcrum cap on the 2.5L six-cylinder diesel. It seats between the tensioner fulcrum cap and its housing, sea...

Cylinder Head Gasket seals the cylinder head to the block on the 2.5L six-cylinder diesel, sealing the combustion chambers along with the coolant a...

Absorber Shock

Tensioner Pulley for the ancillary drive belt on the BMW M51D25 2.5L 6-cylinder diesel engine. The ancillary drive belt powers auxiliary component...

Air Conditioning Compressor Pulley - the driven pulley at the front of the air conditioning compressor, running in the auxiliary drive belt circuit...

Auxiliary Drive Belt Tensioner Pulley - the idler wheel carried on the automatic belt tensioner arm in the auxiliary drive circuit of the 2.5L six-...

O-Ring seals the thermostat housing on the 2.5L six-cylinder diesel. It seats at the thermostat housing joint in the engine cooling circuit, seali...

Gasket manifold inlet P38 BMW M51 2.5L straight 6 cylinder diesel

Alternator for the 2.5L 6-cylinder BMW turbo diesel engine. The alternator is the core component of the charging system. Driven by the auxiliary d...

Coolant Temperature Sensor for the engine cooling circuit, threaded into the coolant gallery in the cylinder head. The sensor's resistance varies ...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Brake Hose for the rear braking circuit - the flexible jump hose linking the chassis-mounted brake pipe to the rear axle. Carrying hydraulic press...

Air Suspension Compressor Filter for the Electronic Air Suspension (EAS) system — the inlet filter on the air compressor intake. The filter cleans...

O-Ring for the electronic air suspension pipework - the seal that sits inside the collet fitting where an air pipe enters a valve block, air spring...