Products

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

EGR Blanking Kit replaces the exhaust gas recirculation (EGR) valve on the 300 Tdi engine, sealing the EGR port on the intake manifold so exhaust g...

Centre Plate Gasket for the LT77 5-speed manual gearbox. This gasket seals the joint between the main casing sections of the LT77 gearbox, prevent...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

O-Ring - an elastomer seal used at the oil cooler pipe connection within the engine oil cooler circuit. It seats in the union between the oil cool...

Front driveline propellor shaft connecting the transfer box output to the front axle differential within the drive mechanism. (60cm in 65cm) Trans...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

UJ Fitting Kit

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Synchro Shift Plate - a shifting plate (shift key) within the synchroniser assembly of the five-speed manual gearbox. It locates in the synchronis...

Inlet Valve Stem Seal for the cylinder head valve train on the V8 petrol engine. The seal fits over the inlet valve guide and wipes the valve stem...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...

Drain plug

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Wheel Bearing Kit - Rear Axle - Non-ABS

Hub Bearing Kit - Front - Non-ABS

Centre Silencer for the 4.2L V8 petrol exhaust system on the Range Rover Classic 108-inch long-wheelbase LSE. Positioned in the mid-section of the ...

Washer is an M12 plain flat washer for use with M12 threaded fasteners. Fitted beneath a bolt head or nut, it provides a flat bearing surface that...

Lock Washer is a locking washer fitted between a nut or bolt head and the mating surface at a threaded joint. It maintains clamp load and resists ...

Rear Fuel Tank Assembly is the main fuel storage vessel of the fuel system, mounted at the rear of the vehicle. It holds the fuel supply and feeds...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Fuel Filter Assembly within the diesel fuel supply circuit, removing contaminants from the fuel before it reaches the injection system. Installed ...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Alternator – V8 Petrol – Less Pulley The engine-driven charging unit that powers the electrical system and maintains battery charge. Lucas A127i ty...

Alternator – V8 Petrol – Narrow Polyvee Belt The engine-driven charging unit that powers the electrical system and maintains battery charge. Lucas ...

Alternator – 300TDi The engine-driven charging unit that powers the electrical system and maintains battery charge on the 2.5L 300 Tdi diesel engin...

Cable Clip - strap-type retaining clip for cable and harness routing. Secures wiring looms or hoses to body panels or chassis members, preventing ...

Cigar Lighter Assembly - facia-mounted 12V cigar lighter, comprising the socket body and the heating element that seats in it. The element is push...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...