Products

Steering Gear Ball Joint is the articulating joint in the steering linkage that connects the track rod to the steering arm. Its ball-and-socket co...

Thermostat regulates coolant flow within the engine cooling system of the 3.0L V6 diesel. It remains closed during warm-up to bring the engine qui...

Starter Motor for the engine starting system, mounted at the engine-to-transmission bellhousing. When cranking, the integral solenoid drives the p...

Fuel Pump Support Housing Seal seals the mounting interface of the high-pressure fuel pump support housing on 2.0L Si4 petrol engines. The high-pr...

CV Boot Kit for the front drive shaft constant velocity joint, providing the components required to renew the protective boot. The CV joint boot r...

CV Boot Kit for the rear drive shaft constant velocity joint, providing the components required to renew the protective boot. The CV joint boot re...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Top Radiator Hose connects the engine outlet to the upper radiator inlet, carrying hot coolant from the engine to the radiator to be cooled. It fo...

Radiator Hose fitted as the upper (top) hose in the engine cooling circuit, between the engine coolant outlet and the radiator inlet. Carries hot ...

Radiator Hose connecting the radiator to the engine coolant vent elbow (degas / deaeration line) in the cooling circuit. Routes coolant between th...

Inlet Manifold Gasket for the left-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifold...

Inlet Manifold Gasket for the right-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifol...

Cover - Mirror Housing

Mirror Housing Cover for the left-hand exterior door mirror, the outer cap that fits over the mirror housing. Supplied primed and requires paintin...

Thermostat and Housing for the engine cooling circuit, supplied as the thermostat pre-assembled in its housing. Regulates coolant flow to bring th...

Anti-Roll Bar Link - Front connects the front anti-roll (stabiliser) bar to the suspension, forming part of the front anti-roll bar assembly. The ...

Drive Belt Tensioner - maintains correct tension on the front accessory (auxiliary) drive belt. The sprung tensioner assembly applies constant loa...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Secondary Drive Belt Idler guides and maintains tension on the secondary (supercharger) drive belt within the front-end accessory drive. The idler...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Radiator Ventilation Hose for the engine cooling system's degassing circuit. The hose vents air and coolant vapour from the top of the radiator to ...

Mass Air Flow Sensor is part of the air intake system, mounted in the intake ducting downstream of the air filter. It measures the mass of air dra...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

O-Ring Kit - a set of eight O-ring seals for the heater and air-conditioning unit. The kit provides the sealing O-rings needed when servicing or r...

Intercooler - the charge-air cooler in the turbocharged induction system. Fitted between the turbocharger outlet and the engine intake, it cools t...

Caliper - Assembly - Rear RH - RS3 R5

Caliper - Assembly - Rear RH - RS3 R5

Caliper - Assembly - Rear LH - RS3 R5

Caliper - Assembly - Rear LH - RS3 R5

Electric Parking Brake Actuator - the motor-gear unit that mounts on a rear brake caliper and applies or releases the parking brake electrically. ...

Propshaft

Rear Suspension Arm - an upper control arm in the rear multi-link suspension assembly. It connects the rear subframe to the wheel hub carrier, loc...

Parking Sensor is an ultrasonic sensor for the Park Distance Control (parking aid) system. Mounted in the bumper, it emits and receives ultrasonic...

Exhaust Crossover Pipe carries exhaust gas between the two cylinder banks of the 3.0 V6 diesel engine, routing the outlet of one manifold across th...

Nut and Retainer - an M10 nut with a captive retainer used at the front crossmember of the front suspension. The retainer locates and holds the nu...

Water Pump for the fuel-fired heater (FFH) circuit. This auxiliary electric pump circulates coolant through the fuel-fired pre-heater. It moves he...

Vacuum Pump Seal - the sealing ring for the engine-mounted vacuum pump. The vacuum pump generates the vacuum used by the brake servo; this seal cl...

Oil Filter and Cooler is a combined assembly within the engine lubrication circuit, integrating the oil filter housing with the engine oil cooler. ...

Lower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...

Anti-Roll Bar Bush - Front is a rubber insulator that mounts the front anti-roll (stabiliser) bar to the vehicle body. Working together with its m...

Rear Air Spring - the right-hand rear air spring (air bellows) of the electronic air suspension system. It supports the rear corner load in place o...

Rear wheel bearing kit contains the wheel bearing, circlip and new hub nut.

Brake Pad Wear Sensor - Front The electronic brake pad wear sensor for the front axle, part of the braking system's pad-wear warning circuit. It lo...