Products

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

Shock absorber bush (eye), anti roll bar bush

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Polyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...

Differential Housing Gasket - Brass seals the joint between the differential housing and the axle casing, preventing oil leaks from the differentia...

Carburettor Inlet Seal for the Zenith carburettor, in the engine air intake system. It seals the joint between the carburettor air intake and the ...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Interior and Instrument Light Switch is the dashboard-mounted switch controlling the cabin interior light and the instrument panel illumination. W...

Third-Speed Mainshaft Gear for the manual gearbox. It is the 3rd-speed gear carried on the gearbox mainshaft, meshing with its layshaft gear to pr...

Gear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...

Spiralox Ring is the spiral-wound retaining ring that secures the front half shaft at the drive shaft and hub of the front axle. Seated in a machi...

Wheel Cylinder Bleed Screw fits into the bleed nipple port of the wheel cylinder in the drum brake assembly, allowing the hydraulic circuit to be p...

Distance Piece is the spacer fitted to the front halfshaft within the front axle and hub assembly. It sets the correct positioning of the halfshaf...

Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Timing Chain Locking Plate for the timing chain drive of the 2.25L and 2.5L 4-cylinder petrol engine. The plate locks the camshaft sprocket retain...

Gearbox Stud is a 1 3/4" threaded stud used in the gearbox and transfer box assembly. It provides a fixed threaded anchor for clamping casing join...

Hot plug hot spot 2.25 diesel

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Series 2, 2A, 2B and Series 3: - 1-Ton, Lightweight and Militairy models. Series 1: - 107".

Coolant Temperature Sender is a thermistor-type sensor threaded into the engine coolant circuit that produces a varying electrical resistance in re...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Wheel Nut A single-chamfer wheel nut that secures the road wheel to the hub studs. The chamfered seating face centres and clamps the wheel against...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Clutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...

o-ring sealing shaft reverse gear LT95 4-speed - S3 109" stage one V8 - 110" V8 4-speed manual - RRclassic 4- speed manual - 101" Forward Control

Handbrake Gasket for the transmission handbrake (parking brake) assembly, sealing the mud shield (oil catcher) against the brake back plate. It ke...

Wheel Stud, splined repair type, for restoring a worn or enlarged stud hole in the hub or drive flange. The stud is splined at one end so it can b...

Reverse Gear for the main manual gearbox assembly. When reverse is selected, this gear engages the reverse idler to invert the rotation passed fro...

Clevis Pin - a linkage pin used in the accelerator and throttle control. It joins the throttle cable clevis to its operating lever, allowing the l...

Front U-bolt

U-Bolt - a spring-to-axle clamp in the front suspension. It wraps over the front axle and passes through a spring plate on the underside of the le...

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Silencer Exhaust 2.6

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Intermediate Exhaust Pipe for the 2.6L 6-cylinder petrol engine. This is the centre section of the exhaust system, connecting the front pipe to th...

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...

Front Exhaust Pipe for the 2.6L 6-cylinder engine fitted to Series II, IIA, and III Land Rovers. This pipe forms the primary section of the exhaus...

Exterior Mirror - Round Arm is a complete wing mirror assembly comprising a round convex mirror head and a standard-length mounting arm, designed f...

Radiator Panel Screw is a fixing screw for the radiator and fan cowl assembly. It secures the radiator panel and fan cowl to their mounting, holdi...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Injector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Pipes (4)

Injector Pipe No.2, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...