Products

Rear Door Step Assembly, a spring-loaded folding step forming part of the rear body equipment. It bolts to the rear cross member below the rear end...

Front Headlamp - Right-Hand - the complete headlamp unit for the right-hand side of the front lighting assembly, comprising the reflector, lens and...

Front Headlamp - Left-Hand - the complete headlamp unit for the left-hand side of the front lighting assembly, comprising the reflector, lens and b...

Headlamp Assembly for the right-hand side of left-hand-drive Discovery 1 variants, forming part of the front exterior lighting system. This is a c...

Headlamp Assembly - Front, Left Hand for left-hand-drive applications, part of the front exterior lighting circuit. The unit combines the reflecto...

Rear Mudflap Kit for the twin-exhaust configuration, mounting behind the rear wheels to deflect mud, water and road debris away from the bodywork a...

Piston Ring Set for the engine bottom end — the compression and oil-control rings that seal the pistons in their bores. Fitted into the piston rin...

Piston Ring Set Standard. 2.25 / 2.5 Diesel (Per Piston)

Non-Return Valve - Brake Vacuum - the one-way valve in the vacuum line between the engine and the brake servo, part of the master cylinder and serv...

Steering Damper Stabiliser - a hydraulic damper fitted within the steering linkage assembly to control the oscillation and vibration transmitted th...

Dog Guard - Loadspace - a framed barrier fitted behind the rear seat backs, separating the rear loadspace from the passenger compartment. It stops...

Fuel Injector Pipe - Cylinder 2 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...

Fuel Injector Pipe - Cylinder 3 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...

Fuel Pipe - Cylinder No.4 for the 200TDi 2.5L four-cylinder turbodiesel, part of the high-pressure fuel injection circuit. This steel injection pi...

Inlet Manifold Gasket seals the joint between the inlet manifold and the cylinder head on the 2.5L VM turbo diesel engine. It maintains the air se...

Water Pump Gasket for the 2.4L and 2.5L VM diesel engine, sealing the interface between the water pump housing and the engine block. This gasket i...

Side Step Set - a pair of rubber-topped side steps with a chevron tread surface, mounted along the lower body to provide a foothold when entering a...

Anti-Roll Bar Kit comprising both front and rear anti-roll bars for the suspension system, supplied complete with standard rubber bushes and fittin...

Anti-Roll Bar Kit - Rear

Oil Pump Repair Kit - renews the oil pump of the LT77 and LT85 five-speed manual gearbox. The pump is housed in the gearbox extension casing and ci...

Bulkhead Outrigger is a structural bracket that supports the right-hand side of the bulkhead and ties it to the chassis frame, carrying the load wh...

Bulkhead Outrigger is a structural bracket that supports the left-hand side of the bulkhead and ties it to the chassis frame, carrying the load whe...

Chassis Outrigger - Rear for the Defender 110, forming part of the ladder-frame chassis structure at the rear of the vehicle. The rear outrigger i...

Clutch Repair Kit - V8

Clutch Repair Kit for the Land Rover Series III clutch assembly. The kit renews the friction and engagement components of the single dry-plate clut...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Dog Guard - a half-height mesh guard that fits across the loadspace to separate it from the passenger cabin, keeping pets or cargo behind the rear ...

Cylinder Head Gasket Kit for the 2.4L and 2.5L VM diesel engine, covering the ancillary sealing components required during cylinder head removal an...

Side Steps with Mudflaps are a bolt-on exterior accessory fitted along the lower body sides, supplied as a matched left-and-right pair. Each step ...

Dog Guard for the rear loadspace, forming a rigid partition between the load area and the passenger compartment. Fabricated from tubular steel wit...

Rear Mudflap Kit mounts behind the rear wheels at the lower edge of the body, deflecting road spray, mud and stones thrown up by the tyres away fro...

Brake pad retention kit for STC2956, STC9187

Brake pad kit rear

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Front Radius Arm Mount Bracket forming part of the front suspension mounting on the chassis. The bracket locates on the chassis outrigger section a...

Front Radius Arm Mount is the chassis bracket that anchors the front radius arm to the chassis on the left-hand side. The radius arm controls fore...

Rear Radius Arm Mount is the chassis bracket that anchors the rear trailing link to the chassis on the right-hand side. The trailing link controls...

Rear Radius Arm Mount is the chassis bracket that anchors the rear trailing link to the chassis on the left-hand side. The trailing link controls ...

Front Seat Spring - Left-Hand, forming part of the front seat base assembly. This spring sits within the seat base structure on the left-hand fron...

The Seat Spring Rear Outrigger is a key component designed for the Defender 110/130 models. This high-quality rear seat spring outrigger supports t...

Rear Upper Spring Seat - non-handed, part of the rear coil spring suspension mounting. The seat is the chassis-side mounting that locates the top ...

Outrigger is a tubular structural member that bolts to the rear of the chassis to support the body and rear cross-member, transferring load into th...

Outrigger is a tubular structural member that bolts to the rear of the chassis to support the body and rear cross-member, transferring load into th...

Rear Crossmember With Extensions for the Defender 90 chassis. The crossmember forms the rearmost structural section of the chassis frame and carrie...

Rear Cross Member with extensions - the rearmost transverse structural member of the ladder-frame chassis. It ties the two main chassis rails toget...

Front Chassis Leg is the forward structural section of the chassis frame on the right-hand side, also known as the front dumb iron. It carries the...