Products

Rubber Floor Mat Set protects the cabin footwells against mud, water and general dirt. The moulded rubber surface contains spills and loose debris ...

Rubber Floor Mat Set protects the cabin footwells against mud, water and general dirt. The moulded rubber surface contains spills and loose debris ...

Side Sill Tread Plate Set - stainless steel entry sill protectors. A set of four stainless steel tread plates covering the front and rear door sil...

Clutch Pedal Torsion Spring is a return spring for the clutch pedal, fitted within the pedal box assembly on manual transmission vehicles. It prov...

Block

Parking Brake Switch mounts on the handbrake lever assembly and operates the handbrake warning lamp in the instrument cluster. When the parking br...

Sunroof Seal for the upper frame of the factory tilt-and-slide sunroof assembly. The seal seats around the upper sunroof frame and bears against t...

Sunvisor Retainer - the clip that holds the sunvisor in its stowed position against the headlining. The retainer fixes to the headlining and recei...

Anti-Roll Bar Bolt Protector for the rear suspension. It fits over the rear anti-roll bar mounting strap and its retaining bolt, shielding the fixi...

Anti-Roll Bar Bush for the rear suspension. It locates and insulates the rear anti-roll bar (stabiliser bar) at its mounting to the chassis, allowi...

Anti-Roll Bar Bush for the rear suspension. It locates and insulates the rear anti-roll bar (stabiliser bar) at its mounting to the chassis, allowi...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Door Lock Housing for the door latch assembly, finished in black. The housing carries the latch mechanism that engages the striker on the body aper...

Pillar Trim - the lower interior trim panel for the left-hand B-pillar. It covers the lower section of the B-pillar inside the cabin on the passen...

Luggage Tie-Down Hook is an anchor point fitted in the loadspace (luggage compartment) area. It provides a fixed loop to which restraint straps or...

Oil Pump Shaft & Gear for the 3.5L V8 petrol engine, part of the lubrication system. The shaft and its drive gear transmit rotation from the ca...

Distributor Drive Gear for the Rover 3.5L V8 petrol engine. The gear forms part of the ignition distributor drive assembly, transferring rotationa...

Coolant Pipe is a rigid coolant transfer pipe in the cooling circuit of the 3.5L V8 (twin-carburettor) petrol engine. It carries coolant between t...

Bracket

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

Flame Trap is the crankcase breather filter fitted in the rocker cover breather circuit of the V8 EFI petrol engine. Connected in the crankcase ve...

Exhaust O-Ring Gasket for the 3.5L V8 petrol engine, sealing the joint between the exhaust manifold and the downpipe. This copper sealing ring loc...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Breather cap for the rocker cover, part of the engine crankcase ventilation system. Fits the 2.25L four-cylinder petrol and diesel engines.

Zenith Carburettor for the 2.25L petrol engine, part of the fuel and induction system. It meters fuel into the incoming air stream to form the air/...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Joint Washer sealing the carburettor to the inlet manifold on the Stage 1 V8. Forms the gasket joint between the carburettor base and the manifold...

Injector Leak-Off Pipe for the 2.25L and 2.5L naturally-aspirated diesel fuel injection circuit. This spill-return pipe connects the return unions ...

Electronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Crankshaft with Bearings for the 2.25L 4-cylinder petrol engine. The crankshaft converts the reciprocating motion of the pistons into rotational o...

Power Steering Belt is the V-belt that drives the power steering pump from the crankshaft pulley, in the non-air-conditioned engine configuration. ...

Crankshaft Pulley for the 2.25L and 2.5L 4-cylinder petrol engine. It mounts on the nose of the crankshaft and drives the cooling fan, water pump a...

Cooling Fan Assembly for the engine cooling circuit, mounted at the front of the engine and driven from the water pump pulley. It draws air through...

Coolant Bypass Hose for the 4-cylinder petrol and naturally-aspirated diesel engines (non-TDi). It forms the bypass path of the engine cooling cir...

Water Pump Gasket for the engine cooling system, sealing the water pump mounting face against the engine block. Fitted to the 11L engine block ver...

Viscous unit

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

Cap Plug for the rocker shaft on 2.25L and 2.5L 4-cylinder petrol and diesel engines. The plug seals the end of the rocker shaft within the cylind...

Rocker Shaft - the hollow shaft that carries the rocker arms in the valvetrain, mounted across the cylinder head rocker pedestals. The rocker arms...

Cylinder Head Gasket for the 2.25L and 2.5L 4-cylinder petrol engine. This gasket is fitted between the cylinder head and the engine block, sealin...