Land Rover Discovery 2 Parts

Rear Shock Absorber fits in the rear suspension, damping spring and axle movement to keep the tyres in contact with the road surface. Gas-charged ...

Synchroniser Assembly for 5th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The sliding sleeve is moved by the fifth-gear ...

Front Shock Absorber fits in the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface....

Wheel Arch Kit - set of replacement wheel arch mouldings for the outer body panels. The mouldings cover the joint between the body panel and the w...

Flywheel Clutch Kit - TD5

Wheel Arch Trim Kit providing a full six-piece set of extended wheel arch flares that fit over the standard arches. The flares extend approximatel...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Mounting Bracket - support bracket in the suspension system. Secures suspension components to the chassis. Used in air suspension and active anti-...

Wiper Motor Grommet for the rear screen wiper assembly. It seals the aperture in the rear door or tailgate where the wiper motor spindle passes thr...

Underside Protection Bar - a front underbody protection member for the body and chassis. Mounted transversely across the chassis at the front end,...

Centre Differential Lock Lever Kit - LT230 - linkage assembly that adds a manual centre differential lock control to the LT230 transfer case. The ...

Steering Box - With Drop Arm - Right-Hand Drive for the Discovery 2 power steering circuit. This Adwest steering box assembly includes the integra...

Side Runner - Discovery 2

Wheel Arch Kit is a set of 75 mm extended wheel arch extensions that give coverage for wider tyres and wheel spacers. The 75 mm profile clears tyr...

Silicone Turbo Hose Kit - a four-piece set of silicone hoses that carry pressurised charge air through the turbocharger and intercooler circuit on ...

Bow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...

Steering & Sump Guard - underbody skid plate. This guard fits beneath the front of the vehicle to shield the steering linkage and the engine s...

Poly-Vee Drive Belt for the Rover V8 petrol engine, in the specification fitted to vehicles equipped with ACE (Active Cornering Enhancement) and ai...

High Note Horn - the higher-pitched element of the dual-tone warning horn assembly. Mounted behind the front grille or valance and paired with a l...

Shock Absorber - Rear is a hydraulic damper in the rear suspension, mounting between the axle and the chassis. It damps oscillation of the rear co...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Air Flow Sensor - V8 is the mass air flow (MAF) sensor for the V8 EFI petrol engine, forming part of the air cleaner and intake assembly. Mounted ...

Rock Sliders

Rear Air Spring Conversion Kit replaces the rear air suspension with conventional coil springs. It removes the self-levelling air springs from the...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Watts Linkage Bush Kit for the rear Watts linkage, which locates the rear axle laterally and keeps it centred through suspension travel. This kit ...

LED Number Plate Lamp - rear licence plate lamp using LED illumination. Mounted above the rear number plate, the lamp illuminates the plate for ni...

Radius Arm Bush - Rear for the rear radius arm. The bush is pressed into the radius arm eye and forms the compliant joint between the radius arm a...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Radius Arm Bush for the front radius arm within the coil-sprung suspension assembly. The bush carries the radius arm at its chassis mounting. The ...

Head Set 4.0/4.6 with Bolts - V8

Brake Master Cylinder Assembly - the hydraulic actuator at the head of the braking circuit, mounted to the brake servo. Force from the pedal, boost...

Engine oil pump assembly for the Td5 2.5L 5-cylinder turbo diesel, forming part of the engine lubrication circuit. The pump is driven from the cra...

Plain Washer is an M12 plain washer used at the rear propshaft flange fixing. It seats under the bolt head or nut at the propshaft flange, spreadi...

Polyurethane Ball Joint Boots for the front axle upper and lower ball joints. These flexible boots seal over the ball joint to retain grease and ke...

ACE High-Pressure Pipe - Rear Lower within the Active Cornering Enhancement hydraulic circuit. This pipe carries hydraulic pressure from the ACE v...

Cooling Fan for the engine cooling circuit, driven from the water pump pulley and drawing air through the radiator core. The viscous coupling (fan...

Front Timing Cover for the V8 petrol engine, incorporating the engine oil pump. Closes the front of the cylinder block over the timing gear and ho...