Genuine Land Rover Parts

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Wiper arm Defender RHD 2A on

Tailgate Hinge Bracket Cover - trim cover for the rear tailgate hinge bracket. The cover fits over the tailgate hinge bracket, concealing and prot...

Screw for securing the rear reflector, fog lamp, and reverse lamp assembly on the Land Rover Defender. Used to retain the lamp cluster components ...

Piston Assembly for the 2.5L 4-cylinder turbo diesel engine, machined to +0.020" oversize for a rebored cylinder block. The piston transfers combu...

Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...

Sill Panel - LH for the Defender 110 Station Wagon and Crew Cab body variants, forming the exterior body panel along the left-hand lower sill line ...

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Washer for use in general fastening applications across the Defender and Range Rover Classic. This plain washer distributes clamping load across t...

Bezel - Vent Air Louvre LH

BEZEL - VENT AIR LOUVRE RH Defender Puma 2007 - 2016

Conrod

Upper Steering Column Shroud is the moulded cover fitted over the top section of the steering column. It encloses the upper column and the mountin...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Carburettor Overhaul Kit for the 2.25L four-cylinder petrol engine. The kit renews the perishable sealing and metering components of the carburetto...

Double Clip for routing and securing battery cables. This twin clip retains two leads together, holding the cabling in place along its run.

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...

Side Window Filler Strip for the rear side window assembly. The filler strip closes the gap along the side window channel, completing the seal and...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Splash Seal

Air Duct - the induction duct of the air cleaner assembly, carrying filtered air from the air cleaner outlet to the turbocharger compressor inlet. ...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Hose - Filler Pipe

Gear Lever Boot - a flexible gaiter that seals around the base of the gear-change lever where it passes through the transmission tunnel. It closes...

Mudflap

Mudflap

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Seat Belt

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Front Bumper End Cap - Outer, installed at the outer section of the front bumper assembly. This component forms part of the Front Bumper & Bum...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Front Cover Gasket for the LT85 five-speed manual gearbox, G20C unit. This gasket seals the front cover to the main gearbox casing, preventing oil...

Tailgate Cable Stud is the anchor point for the rear tailgate support cable. Mounted on the rear body, the stud receives the end of the tailgate c...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Synchro Cone (Baulk Ring) - LT95 4-Speed Gearbox This synchro cone, also known as a baulk ring, is a component of the synchroniser assembly within...

Camshaft Washer is a retaining washer used at the front of the camshaft within the timing drive of the 3.5L V8 petrol engine. It is fitted at the ...

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Fuel Tank Vent Hose - part of the fuel tank ventilation circuit, allowing the tank to breathe and equalise internal pressure as fuel level and temp...