Genuine Land Rover Parts

Clutch Pedal Spring Bush is a small bush fitted to the clutch pedal assembly on the Defender 90/110, locating the pedal return spring. The bush se...

ROVER Lettering Emblem - silver, 35 cm - for Defender (2007-2016). This is the adhesive silver lettering strip that spells out "ROVER" on the exte...

Emblem - LAND - Silver - 28cm is the "LAND" lettering badge that forms part of the bonnet exterior script. The silver badge measures 28 cm in leng...

Door Latch Stud Plate for the front door latch mechanism. The striker stud plate mounts to the body pillar and provides the fixed engagement point...

Torx Bolt from the Land Rover fixings and fasteners range. A Torx-drive bolt for use in Land Rover assembly applications requiring a Torx head fix...

Body Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Self-Tapping Screw, No.6 x 3/8". A self-tapping fastener that forms its own thread as it is driven, used to secure body panels, trim and light fix...

Rear Fog Switch for the dashboard switching circuit. A push-push type switch that controls activation of the rear fog lamp circuit. Mounts in the ...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Starter Motor Brush Kit for the Lucas M113-type starter motor in the engine starting system. The brushes bear on the armature commutator to transf...

Heater Control Cable - Heat Outlet for Defender 90 and 110 vehicles. This Bowden cable connects the heat outlet control lever on the heater contro...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Snap Ring

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Inner Ring

Heater Control Pin

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Steering Column Top Clamp secures the upper section of the steering column at its top support within the steering column assembly. It clamps the c...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Washer

Top cover

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Differential Thrust Washer Thrust washer for the differential gears within the Salisbury rear axle. It seats behind a differential gear in the fou...

Door Check Bracket - Rear is a mounting bracket within the rear door check mechanism. It anchors the door checker (door stay) to the body, providi...

Synchroniser Plate - Mainshaft is part of the synchromesh assembly carried on the gearbox mainshaft in the 5-speed manual transmission. It operate...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Fan Cowl Clip is a retaining clip in the engine cooling system. It secures the fan cowl - the shroud that channels airflow through the radiator - ...

Layshaft Shim for the LT77 five-speed manual gearbox, located at the layshaft (countershaft) front cover and bearing. This is a selective shim use...

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Engine Mounting Bracket - Left Hand for the 2.5L 4-cylinder TDi diesel engine. The bracket bolts to the left-hand side of the engine block and car...

Door Striker Support Bracket mounts to the body aperture and carries the front door latch striker, providing the rigid anchor point against which t...

Key Blank for Land Rover lock barrel assemblies. This uncut key blank matches the barrel profile used in door locks, ignition locks, the tailgate, ...