Genuine Land Rover Parts

Rear Door Glass for the right-hand rear door. This is the main window pane that raises and lowers within the door. It is guided by the glass run c...

Rear Side Door Glass for the left-hand rear side door. This is the main window pane that raises and lowers within the door. It is guided by the gl...

Switch - Window Lift - Centre Console - Discovery 1/RRC

Upper Clutch Pipe is the rigid metal section of the hydraulic clutch actuation circuit running from the clutch master cylinder. It carries fluid f...

GENUINE LR camshaft sprocket for Rover V8 engines

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Instrument Bulb Holder for the early Discovery 1, providing the retaining socket for an illumination bulb within the instrument cluster assembly. ...

Brake Pipe Clip secures and routes rigid brake pipe runs within the braking system, holding the pipe against the chassis or body to maintain its ro...

Rear Door Lock Cover Badge - badged cover fitted over the rear door lock aperture, part of the rear door exterior handle and lock assembly. The co...

SRS ECU - the Supplemental Restraint System electronic control unit, commonly known as the air bag control module. It sits at the centre of the SR...

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Alpine Light Weatherstrip for the right-hand side, sealing the fixed alpine light glass into the rear roof aperture of the body. The rubber weathe...

Oil Cooler Pipe for the engine oil cooling circuit on diesel engines, running between the oil cooler and the pump feed. Carries engine oil under p...

Shim bearing differential 0.062""

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Locking Wheel Nut Kit for alloy road wheels, part of the road wheel and fixings assembly. Each locking nut replaces a standard wheel nut at one pos...

Key Wheel Nut

Seal

Split Pin used throughout the handbrake and gearchange linkages. The pin passes through a clevis pin or castle nut and its legs are spread on asse...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Kit - Caliper Brake Pad

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Turbocharger Adaptor Pipe in the induction system of the 2.5L 200 TDi and 300 TDi turbo diesel engines. It forms the connecting pipe between the t...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Elec Door Mirror - LH

Rivet used to secure exterior body panels and mouldings, including front wing and body-moulding assemblies. Installed through the panel to retain ...

Front Grille Badge in gold finish, fitted to the front radiator grille panel. The badge mounts to the grille to carry the marque identity at the f...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Cable Clip for securing and routing cables and wiring to body and chassis structures.

Restrictor - flat 20 mm plain washer used in the suspension link mountings of the coil-sprung live-axle chassis. It is fitted at the radius arm mo...

Washer Pump Assembly for the rear screen washer system. The electric pump pressurises washer fluid drawn from the reservoir and delivers it through...

Wire - Ignition

Lamp

Rubber floor mat set for the passenger compartment, supplied as a complete vehicle set. The mats are shaped to the footwells and drop in over the ...

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Engine Mounting Bracket - 3.5L V8

Heater Pipe Kit - Air Con

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Adjuster

Cooling Fan for the front-end cooling pack on vehicles built with factory air conditioning. The fan draws air through the condenser and radiator a...