Genuine Land Rover Parts

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Fastener used to secure interior door casing panels and body side trim. Retains door casing and rear body panel trim on applicable vehicles.

Torx Flanged Screw - Front Door Latch Assembly for the front door latch mechanism. This Torx-head flanged screw secures the front door latch assem...

Engine Plug - a cylinder head core plug (welch plug) for the Td5 2.5L 5-cylinder turbo diesel engine. Core plugs seal the casting holes left in th...

Sunroof Finisher - perimeter seal trim section for the manual slide sunroof assembly on the Discovery II. The component forms the finishing strip ...

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Grille Grommet - a mounting grommet for the front grille and headlamp surround panel. It seats in the body panel to receive and retain the grille ...

Seat Cushion Pad is the moulded foam cushion forming the seating base of the front seat, sitting on the seat frame beneath the trim cover. It rest...

Rear Lamp Assembly - Discovery 2 - RH

GENUINE LR camshaft sprocket for Rover V8 engines

Cooling Fan for the engine cooling circuit, driven from the water pump pulley and drawing air through the radiator core. The viscous coupling (fan...

Headlamp Bulb Cover is the rear sealing cap that fits over the bulb aperture at the back of the headlamp housing. It seals the housing against dus...

Rear Door Lock Cover Badge - badged cover fitted over the rear door lock aperture, part of the rear door exterior handle and lock assembly. The co...

Plastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...

Lamp Assembly-Rear

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Parking sensor bezel in black, the retaining trim ring that locates a Park Distance Control (PDC) ultrasonic sensor in its bumper aperture. The be...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Key Wheel Nut

Coolant Hose - the top radiator hose in the Td5 2.5L 5-cylinder turbo diesel engine cooling system. This hose forms part of the upper coolant circ...

Coolant Hose - EGR Cooler to Expansion Tank is part of the engine cooling system pipework serving the EGR cooler. It carries coolant between the E...

Coolant Hose connecting the heater circuit to the oil cooler on the Td5 2.5L five-cylinder turbo diesel. The hose carries engine coolant along the...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Sump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. It seals the joint between the oil sump and the cylinder block within the engine lubri...

Kit - Caliper Brake Pad

Adjusting Screw for the Td5 2.5L five-cylinder turbo diesel engine rocker assembly. Sets the clearance at the rocker where it acts on the valve an...

Front Camshaft Oil Seal for the Td5 2.5L 5-Cylinder Turbo Diesel engine, fitted at the timing end of the camshaft within the cylinder head. Seated...

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Turbo Hose for the Td5 2.5L 5-cylinder turbo diesel induction system. Forms part of the air cleaner assembly, ducting filtered intake air from the...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Wiper Blade A front windscreen wiper blade within the wiper assembly. It attaches to the wiper arm and clears the windscreen as the arm sweeps acro...

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Bracket - Mtg

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Lamp

Holder - Cup

Holder - Cup