Genuine Land Rover Parts

Gearbox Mounting - Left Hand - bonded rubber mounting in the transmission mounting assembly, fitted between the gearbox and the chassis crossmember...

Gearbox Mounting - Right Hand - bonded rubber mounting in the transmission mounting assembly, fitted between the gearbox and the chassis crossmembe...

Spring Retainer - Parking Sensor

Parking Distance Control Spring is the retaining spring for the Parking Distance Control (PDC) sensors mounted in the rear bumper. It secures a PD...

Tailgate Window Switch - momentary rocker switch for the electric window lift circuit, mounted in the centre switch console. Finished in black. Th...

Transfer Box Switch Wire Adaptor for the LT230 transfer gearbox. This short harness link connects the main vehicle wiring loom to the switch on th...

Rear Lamp Gasket - the sealing gasket fitted between the rear lamp assembly and the rear body panel. It seals the lamp against the bodywork, preve...

Headlamp Cover, Right-Hand Side. Protective cover fitting over the right-hand front headlamp lens assembly, for facelift-specification vehicles. D...

Front Fog Lamp - Left-Hand for the front bumper lighting assembly. This lamp mounts in the front bumper fog lamp aperture and provides supplementa...

Front Fog Lamp - Right-Hand for the front bumper lighting assembly. This lamp mounts in the front bumper fog lamp aperture and provides supplement...

Headlamp Assembly - complete front headlamp unit for the front exterior lighting assembly, in the vented housing specification. The vented housing...

Canister Vent Solenoid for the evaporative emission control (EVAP) system. The solenoid controls the fresh-air vent side of the charcoal canister....

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Secondary Air Injection Hose - flexible hose in the secondary air injection system of the V8 petrol engine. It carries pumped air through the seco...

Secondary Air Rail Connector - connector in the secondary air injection system of the V8 petrol engine. Secondary air injection introduces fresh a...

Plug - Drain

Automatic Gearbox Sump Plug - the threaded plug that seals the drain point on the ZF automatic transmission oil pan. Removed to drain the transmis...

Fuel Block Connector - fuel block and pressure regulator assembly in the fuel supply and return circuit of the Td5 2.5L 5-cylinder turbo diesel. I...

Crankshaft Pulley - for the 4.0L and 4.6L V8 EFI petrol engine. Mounts to the nose of the crankshaft at the front of the engine and drives the acc...

Engine Mount - Rubber - Diesel supports the engine on the chassis and isolates it from the vehicle structure. The bonded rubber element absorbs co...

Engine Mounting for the V8 petrol engine, forming part of the powertrain support system. It locates between the engine bracket and the chassis, ca...

Foam Pad - Air Intake Deflector seals the air intake deflector in the scuttle area, where fresh air is drawn into the heating and ventilation syste...

Dial Illumination Bulb for the climate control panel, providing backlighting for the heating and ventilation controls. It seats behind the switch ...

Dial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...

A/C Condenser Fan Assembly - electric cooling fan for the air conditioning condenser. Mounted at the front of the vehicle ahead of the cooling pac...

Blower Motor Resistor Pack - speed control for the heater and air conditioning blower motor, also referred to as the air conditioning switch. The ...

Air Intake Plenum Extension Moulding in black, the moulded panel that sits in the scuttle area between the rear edge of the bonnet and the base of ...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

Pin - Split

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...