Genuine Land Rover Parts

Front Lower Engine Mounting is the lower insulator supporting the engine at the front of the mounting system. It locates the engine to the subfram...

Upper Knuckle Bolt is a hex-head bolt that retains the upper knuckle joint within the hub and knuckle assembly. It clamps the upper knuckle to the...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Oil Cooler Return Connector is a connector fitting in the engine oil cooler circuit of the 2.2L diesel engine (DW12). It joins the oil cooler retu...

Oil Filter Housing Cover for the oil cooler and filter housing on the 2.2L DW12 turbo-diesel engine. The cover closes the oil filter housing, reta...

Windscreen Washer Pump Grommet seals the washer pump into the windscreen washer fluid reservoir. This rubber grommet fits into the reservoir body ...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Coolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...

High Voltage Water Heater for plug-in hybrid (PHEV) applications, operating in the high-voltage coolant heating circuit. The unit heats engine coo...

Crankcase Breather Cover - crankcase ventilation cover on the 2.0L AJ20P4 petrol engine, forming part of the crankcase emission control assembly. ...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Accessory Drive Belt for the engine accessory (ancillary) drive on 2.0L GTDi and second-generation 2.0L turbocharged petrol engines. The belt is d...

Coolant Degas Separator, part of the engine cooling circuit on 2.0L Ingenium (AJ200) petrol applications. The degas separator removes entrained ai...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Wheel hub bearing for the front and rear knuckle and hub assemblies. The bearing carries vehicle load between the hub and the knuckle and allows t...

Spark plug for the ignition system of the Ingenium petrol engine range - 1.5L AJ20P3, 2.0L AJ20P4 / AJ200P and 3.0L AJ20P6 / AJ22P6, including plug...

Variable Timing Solenoid - camshaft timing oil control valve in the variable valve timing system of the Ingenium engine range. The solenoid is an ...

Front Brake Pads for the front axle disc brake assembly, supplied as a full axle set covering both front calipers. The friction pads are clamped a...

PCV Valve Service Kit for the crankcase ventilation circuit of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4). The positive crankcase ventilatio...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

Balance Shaft - counterweighted shaft forming part of the engine balancer assembly in the lower block. Driven from the crankshaft and running at t...

Suspension Arm - Front - LH - front suspension arm (wishbone) in the front independent suspension assembly, left-hand side. The arm locates the fr...

Suspension Arm - Front - RH - front suspension arm (wishbone) in the front independent suspension assembly, right-hand side. The arm locates the f...

Brake Pad Set - Front - friction pad set for the front brake caliper assembly, part of the foundation braking system. Supplied in the less-springs...

Coolant Hose - Overflow Container - moulded hose in the engine cooling system connecting to the coolant overflow container (expansion tank). It ca...

Coolant Hose - Overflow - moulded hose in the engine cooling system, forming part of the overflow circuit between the cooling circuit and the coola...

Rear Brake Disc - 325 mm solid disc for the rear axle service brake assembly. The disc locates on the rear wheel hub flange and forms the friction...

Rear Brake Disc - 300 mm solid disc for the rear axle service brake assembly. The disc locates on the rear wheel hub flange and forms the friction...

Front brake disc, 349mm diameter, internally vented, forming part of the front brake disc and caliper assembly. Mounted to the front hub, the disc...

Air Filter - engine air cleaner element, seated in the intake air cleaner housing upstream of the mass air flow sensor and the turbocharger inlet. ...

Drive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...

Bearing Retainer - front bearing retainer within the Front Axle Drive Shaft assembly. The retainer secures and locates the front support bearing o...

Brake Pads for the front axle, part of the front brake discs and calipers assembly. The front pads carry the greater share of the braking load. Th...

Brake Pads for the rear axle, part of the rear brake discs and calipers assembly. The pads are clamped by the caliper pistons against both faces o...

Rear Brake Pad Kit - friction pads for the rear disc brake assembly, mounted in the rear caliper and clamping the rear brake disc. Supplied as a r...

Rear Brake Pads - With Springs - friction pads for the rear disc brake assembly, supplied complete with the caliper pad retaining springs. The pad...

Rear Brake Pad Kit - the friction pads that sit in the rear brake caliper and clamp the rear brake disc, forming the wear interface of the rear dis...

Brake Pads - Rear - With Springs - friction pads for the rear axle, supplied as a complete axle set (one set per axle). The pads locate in the rea...