Genuine Land Rover Parts

Exhaust Mounting is a moulded rubber mounting that suspends the front section of the exhaust system from the vehicle body. The rubber body links t...

Anti Roll Bar Bush locates the anti-roll bar in its chassis mounting bracket, providing a resilient rubber interface between the bar and the subfra...

Coolant Pump Cover for the 2.0L four-cylinder TCIE diesel engine, part of the engine cooling circuit. The cover closes the coolant pump housing an...

Coolant Hose - Radiator Top - upper radiator hose in the engine cooling circuit of the M47 2.0L 16-valve Td4 turbo diesel, automatic transmission a...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Crankcase Breather Hose for the 2.5L KV6 petrol engine, part of the crankcase ventilation system. It carries blow-by gases from the cylinder head ...

Breather Hose connecting the camshaft cover breather outlet to the inlet manifold on the 2.5L KV6 petrol engine. Part of the crankcase ventilation...

A/C Compressor O-Ring seals a refrigerant line union at the air conditioning compressor. The O-ring is clamped between the pipe end fitting and th...

Door Latch Assembly for the left-hand rear side door. Complete latch mechanism that secures and releases the rear side door, engaging the striker ...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Washer Jet Tube Tee Piece - a T-shaped connector in the windscreen washer system. The tee piece connects into the small-bore washer tubing, joinin...

Rivet used to secure exterior body panels and mouldings, including front wing and body-moulding assemblies. Installed through the panel to retain ...

Rear Door Latch Assembly - the latching and locking mechanism for the rear door. It engages the striker on the body aperture to hold the rear door...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Fuel Spill Return Pipe - part of the fuel injection system, connecting the injector leak-off ports to the fuel return line. It collects spill (lea...

O-Ring - Fuel Injector - Diesel - sealing ring in the fuel injector and pipe assembly on diesel engines. The ring seals the injector joint against...

Brake Light Switch for the braking and signalling circuit. Mounted at the brake pedal assembly, this switch closes when the pedal is depressed, co...

Headlamp Assembly - left-hand unit for left-hand-drive vehicles. Supplied as a complete headlamp and flasher unit comprising the housing, reflecto...

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Cap

Cap - Overflow Container

O-Ring - Fuel Injector - Diesel - sealing ring in the fuel injector and pipe assembly on diesel engines. The ring seals the injector joint against...

Snap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...

Inlet Manifold Insert - press-in insert that forms the vacuum take-off union in the upper inlet manifold. The insert is pressed into a machined bo...

Cylinder Head Gasket, 1.20mm thickness, two-hole identification, for the 2.0L L-Series 8V TCIE direct injection diesel engine. The gasket seals th...

Relay - Direction Indicator Flasher is the electronic flasher unit that sets the pulse rate of the direction indicator and hazard warning circuits....

Rear Stop and Flasher Lamp for installation in the left-hand position of the rear bumper. This unit provides the stop lamp and direction indicator...

Headlamp

Headlamp

Headlamp

Clip - retaining clip used in the clutch hydraulic circuit, on the clutch release mechanism and on the clutch master cylinder and its pipework. Th...

Big End Bearing - a connecting-rod (big-end) bearing shell for the 2.5L KV6 petrol engine. Fits between the connecting rod and the crankshaft jour...

Engine Tie Rod - lower torque rod within the engine mounting system. It ties the powertrain to the subframe and resists the fore-and-aft rocking (t...

Engine Tie Rod forms part of the powertrain mounting system, working alongside the engine mounts. This lower tie rod restrains fore-and-aft moveme...

Engine Mounting - right-hand side mounting in the engine mounting assembly. Locates the right-hand side of the engine on its bracket and isolates ...

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Door Latch for the rear end door. Secures and releases the rear end door, engaging the striker on the body aperture and linking to the handle and ...