Genuine Land Rover Parts

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Water Inlet Tube for the engine coolant circuit of the 5.0L V8 petrol engine (AJ133). The tube carries coolant to the thermostat and its housing, ...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

Seal Kit renews the seals at the hydraulic pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The ACE system uses hy...

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Vacuum Pump Gasket for the 4.4L V8 diesel engine. It seals the mating joint between the vacuum pump and its mounting face on the engine, forming pa...

Intercooler Pipe connecting the turbocharger outlet to the intercooler in the charge-air system of the 2.0L AJ200 (Ingenium) four-cylinder diesel e...

EGR Valve Gasket seals the exhaust gas recirculation valve to its mating face within the EGR and front exhaust system. Fitted on the left-hand ban...

Manifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine, mounted in the throttle housing. It measures absolute pressure in the intake...

Solenoid Valve for the air suspension compressor assembly. It forms part of the compressor and air-line circuit, controlling the flow of compressed...

Accessory Drive Belt for the front engine accessory drive. The multi-ribbed belt transmits drive from the crankshaft pulley to the engine ancillari...

Fuel Pump Drive Belt Kit for the rear accessory drive of the 3.0L V6 diesel engine. The belt transmits drive to the high-pressure fuel injection p...

Climate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...

Tube - Active Roll Bar System

Front Brake Disc for the front axle, matched to the size-19 front brake configuration. It mounts to the front wheel hub and rotates with the wheel...

Brake Disc

Exhaust Gas Temperature Sensor for the diesel particulate filter (DPF) system. Monitors exhaust gas temperature in the after-treatment section and...

EGR Gasket Inlet

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Rear timing belt kit - fuel injection pump drive for the 3.0L V6 turbo diesel engine. The rear belt drives the high-pressure fuel injection pump a...

Brake Disc - front axle, internally vented. The disc provides the friction surface that the front brake pads clamp against, converting the vehicle...

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

Blind Anchor Nut - a threaded anchor nut that provides a captive fixing point where the reverse side of the panel is inaccessible. It is used in t...

Service Kit - L405 - 3.0 V6 Die & RRS - 3.0 V6 Die - EA000001 On

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Bracket - Mtg

Bolt - Special is an M22 metric timing gear bolt used in the engine timing gear assembly. This special bolt secures components within the timing g...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Rear Exhaust Clamp in the rear exhaust assembly. The clamp secures the joint between adjacent sections of the rear exhaust, compressing around the...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Camshaft Sprocket is a timing drive gear in the valvetrain, mounted on the end of a camshaft. Driven by the timing chain from the crankshaft, it r...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Anti Roll Bar Link

4

V-Belt

Belt Tensioner Pulley for the auxiliary drive belt system on the 2.7L TDV6 Diesel engine. This pulley maintains correct tension on the auxiliary d...

Hose

Coolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...