Genuine Land Rover Parts

24v dsl long belt

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Loadspace rubber mat for the rear load compartment, part of the interior protection group. The mat is tailored to the loadspace floor and protects...

Washer - Sealing

Auxiliary Drive Belt for the 2.7L TDV6 diesel engine on vehicles without an active roll stabiliser, 2092mm. This ribbed belt transmits drive from ...

Bolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...

Wheel Nut Cap in a silver finish, part of the road wheel and wheel fixings assembly. The cap is a push-fit cover that sits in the wheel face over ...

Wheel Hub with integrated wheel bearing, forming the wheel end of the front and rear suspension assembly. The hub carries the wheel mounting flang...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Service Kit - L405 - 3.0 V6 Die & RRS - 3.0 V6 Die - EA000001 On

Fuel Filter for the 3.0L AJ20D6 diesel engine, part of the fuel filtration circuit. It removes particulate contaminants and water from the diesel ...

Windscreen Washer Pump Grommet seals the washer pump into the windscreen washer fluid reservoir. This rubber grommet fits into the reservoir body ...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Anti Roll Bar Link

4

V-Belt

Belt Tensioner Pulley for the auxiliary drive belt system on the 2.7L TDV6 Diesel engine. This pulley maintains correct tension on the auxiliary d...

Hose

Coolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...

Cap - Overflow Container

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Gearbox Plug

Drive Belt Tensioner - engine front-end accessory drive. Sprung arm carrying an idler pulley that maintains correct tension on the accessory drive...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Water Outlet Hose - lower return hose in the turbocharger lubrication and cooling circuit. Carries coolant from the turbocharger bearing housing b...

Water Connection for the turbocharger coolant feed, lower position, in the turbocharger lubrication and cooling circuit of the 3.0L AJ20P6 Ingenium...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Front Brake Pad Kit - friction pads for the front disc brake caliper. The pads are clamped against the front brake disc by the caliper pistons to ...