Genuine Land Rover Parts

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

bushes needed to machine the Series LT76 transfer case for the High Ratio Gear Set (HGRS.)

Cylinder Head Kit

Battery Cable for the 24V electrical system. This is a battery link cable, connecting the two batteries so they supply the vehicle's 24-volt circu...

Station Wagon Rear Side Window Glass - the small fixed glass pane for the rearmost side window aperture of the Station Wagon body. It glazes the r...

Accelerator Cable connecting the accelerator pedal to the throttle linkage on the 3.5L V8 petrol engine. The cable transfers pedal travel to the c...

GENUINE LR camshaft sprocket for Rover V8 engines

Shim 1.65mm for Layshaft Speed - V8 4

Retainer Oil Seal On Output Housing

Washer - M4 flat washer, used to spread the clamping load of an M4 fastener and protect the panel surface beneath the fixing. Fitted at a number o...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Steering Lever - LH - RHD is the left-hand steering arm that bolts to the front swivel pin housing. It provides the attachment point for the steer...

Output Shaft - Front for the Land Rover transfer gearbox. The front output shaft carries drive from the transfer gearbox to the front propshaft, su...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Screw for securing the window catch on Series hard top body variants. Used in the hard top glazing and catch assembly to retain the window catch m...

Rocker Shaft for the 2.6L six-cylinder petrol engine, part of the valvetrain in the cylinder head. The shaft mounts on the head and carries the ro...

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Master Cylinder

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Engine Mounting Bracket - 3.5L V8

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Front Bumper for the Series II, IIA and III Military Lightweight and Airportable variants, including JC3 specification vehicles. This bumper forms ...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Seal - Oil Pump

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Tube

Strip - Glazing and Sealing