Genuine Land Rover Parts

Spacer - Hinge

Steel Road Wheel - 6.5J x 16, Wolf-style pattern. It provides the mounting surface for a tubeless road tyre and transfers vehicle load from the tyr...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Hook

Differential Pinion Shim - 0.062" selective shim used to set the pinion position within the differential (final drive) assembly. Fitted at the pin...

Rear Indicator Amber Lens

Side Lamp Lens

Side Lamp Lens in white glass for the Lucas military-pattern side lamp. The lens presses into the side lamp body to seal the bulb aperture and diff...

Genuine Accelerator Lever 1964-83.

Shackle Pin for the rear shackle of the front leaf spring. The pin pivots the spring shackle at the rear eye of the front road spring, locating th...

Battery Cover Frame - Top is the upper frame section of the battery cover assembly. It forms the top of the battery enclosure, locating and retain...

Wiring Harness Set is the main electrical loom that carries power and signal connections through the vehicle's electrical system, tying the chargin...

Washer

Screw, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...

Conrod Bearing Set (big-end bearings) for the 2.6L 6-cylinder petrol engine. The shells sit between the connecting-rod big-ends and the crankshaft...

Door Hinge is the upper front door hinge for the right-hand side, part of the front door mounting assembly. It bolts to the body pillar and to the...

Needle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...

Contact Set for Elec. Fuel Pump

Cup Washer is a dished washer used at the gearbox tie-rod (stabiliser rod) to chassis mounting on Series models. The cupped profile seats against ...

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Hose Clip Spring is the spring connector clip for the heater demister and air outlet pipes. Retains the demister ducting and outlet flaps within t...

Inlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...

Filler Fuel

Bolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

Coolant Temperature Sensor - screws into the thermostat housing as part of the engine cooling system. It senses coolant temperature in the thermos...

Rear Body Capping is the capping strip fitted along the top edge of the rear body side, covering and protecting the exposed panel edge and giving t...

Door Lock - left-hand anti-burst latch assembly for the door closing and locking mechanism. The anti-burst design resists the latch springing open...

Glass