Genuine Land Rover Parts

Spare Wheel Carrier is the mounting bracket assembly that carries the spare wheel on the rear door. It bolts to the rear door and provides the stu...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Amber Switch Bulb for the heated windscreen and auxiliary switches. This small bulb provides the amber illumination within the switch, lighting th...

Bolt for the adjustable rear suspension arm on the Freelander 2 and Range Rover Evoque. This M14 × 85mm special bolt secures the adjustable rear a...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Switch

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Exhaust manifold stud

Sunroof Seal for the manual sliding sunroof. The rubber seal fits around the sunroof aperture and seals the panel against the roof to keep out wate...

Headlamp Gasket for the headlamp mounting assembly. A rubber seal that fits between the headlamp unit and the surrounding body panel, providing a ...

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Window regulator front RH

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Coolant Hose connecting the radiator to the fuel cooler within the engine cooling circuit. It routes engine coolant to the coolant-cooled fuel coo...

Top Radiator Hose for the 2.0L Diesel engine cooling circuit. This upper radiator hose connects the engine coolant outlet at the thermostat housin...

Saddle Clip for routing and securing the power steering pipes. This saddle-shaped clip clamps the power steering hydraulic pipes to the chassis or...

Heater Hose - a coolant hose in the heater circuit, connecting the heater to the engine pipework. It carries engine coolant to and from the heater...

Heater Hose forming part of the engine coolant circuit that supplies the heater matrix. This is the feed hose carrying heated coolant from the eng...

Windscreen Glazing Seal - the moulded rubber seal that mounts the windscreen glass into the front bulkhead aperture. It locates and cushions the gl...

Early Seat Diaphragm Door Only - Discovery 1 4

Folding Side Step Mat - tread mat fitted to the folding side access step. Provides a non-slip stepping surface for entry and exit at the side doors.

Pump Injection Ring

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Front Seat Belt Assembly for the Defender occupant restraint system. This complete front seat belt assembly includes the belt, retractor, and buck...

Air Filter Strap securing the air cleaner housing within the engine intake system. Clamps the air filter canister to its mounting on the 2.5L four...

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Mud Flaps shield the bodywork and following traffic from the road spray, mud and stones thrown up by the wheels. Supplied as the right-hand pair f...

Decal name plate

Speaker Bezel is the trim surround that frames a speaker opening in the interior. Part of the in-car entertainment (ICE) installation, it finishes...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Gearbox Top Cover Plate - the cover plate that closes the top aperture of the main gearbox casing. It seals the top of the gearbox over the select...

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Front Brake Anchor Plate (back plate) for the right-hand side, part of the front drum brake assembly. The anchor plate bolts to the axle and carri...

Copper Sealing Washer, 7/16 inch, for hydraulic pipe unions on Series Land Rovers. This annealed copper washer seats under a banjo bolt or pipe un...

Drive Belt short V-profile belt for 24-volt Land Rover applications. Drives ancillary components in the engine accessory belt system.

Core Plug - Cylinder Head A 7/8" diameter core plug (welch/expansion plug) that seals a casting core hole in the cylinder head. It closes the open...

Plain Washer is a flat fastening washer fitted under a bolt head or nut to spread the clamping load across a wider area and protect the mating surf...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...