for Discounts / VAT
for Discounts & Correct VAT
Genuine, OEM, and quality aftermarket Land Rover Defender parts for the classic 90, 110, and 130 (1983-2016) and the new Defender L663 (2020-present). Every component is sourced for verified fitment by VIN and shipped from our Netherlands warehouse as part of our wider Land Rover parts catalogue.
Brake Pad Wear Sensor for the front axle, part of the brake pad wear warning circuit. The sensor is located in the brake pad and carries a wire lo...
View full detailsRelay - 20 A five-pin micro relay, black housing. A five-pin relay is a changeover type: a low-current control circuit energises the coil, which s...
View full detailsVariable Timing Solenoid - camshaft timing oil control valve in the variable valve timing system of the Ingenium engine range. The solenoid is an ...
View full detailsIgnition Coil for the 3.0L AJ20P6 / AJ22P6 six-cylinder petrol engine, part of the ignition system. The coil is switched by the engine control mod...
View full detailsV-Belt for the front-end accessory drive of the 3.0L AJ20P6 six-cylinder petrol engine. The belt is driven by the crankshaft pulley and transmits ...
View full detailsBrake Pad Wear Sensor for the front axle, part of the brake pad wear warning circuit. The sensor is located in the brake pad and carries a wire lo...
View full detailsExpansion Chamber from the air supply unit of the four-corner electronic air suspension system. The chamber is plumbed to the compressor and acts ...
View full detailsBrake Pad Wear Sensor for the front axle, part of the brake pad wear warning circuit. The sensor is located in the brake pad and carries a wire lo...
View full detailsRear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the crankshaft sealing arrangement on the Ingenium engi...
View full detailsDrive Belt - ISG - V-belt in the front-end accessory drive of the 3.0L Ingenium six-cylinder petrol engine, driving the belt-integrated starter gen...
View full detailsCoolant Expansion Tank Cap - pressure cap sealing the coolant expansion (overflow) container in the engine cooling circuit. The cap is a working c...
View full detailsLambda Sensor for the 3.0L AJ20P6 six-cylinder petrol engine, mounted in the exhaust system as part of the fuelling feedback and emission control c...
View full detailsCabin Pollen Filter for the front heating, ventilation and air conditioning intake housing. The element sits in the HVAC filter tray upstream of t...
View full detailsCowl Moulding Clip - retaining clip securing the front cowl (leaf screen) moulding to the body structure. The clip holds the plenum trim panel dow...
View full detailsAccessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...
View full detailsRear Upper Suspension Arm for the rear multi-link suspension assembly. The arm locates the upper end of the wheel carrier relative to the rear sub...
View full detailsAccessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...
View full detailsCabin Pollen Filter for the front heating, ventilation and air conditioning intake housing. The element sits in the HVAC filter tray upstream of t...
View full detailsAccessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...
View full detailsOil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...
View full detailsEGR Inlet Gasket for the exhaust gas recirculation circuit of the 2.0L I4 AJ200 Ingenium diesel engine. The gasket seals the EGR inlet joint on th...
View full detailsSteering Ball Joint - the outer tie rod end in the front steering linkage. Threads onto the steering gear connecting rod and locates in the steeri...
View full detailsTiming Gear Special Nut from the front timing gear assembly, securing the lower primary timing chain guide. The nut locates and clamps the guide a...
View full detailsCabin Pollen Filter for the front heating, ventilation and air conditioning intake housing. The element sits in the HVAC filter tray upstream of t...
View full detailsTiming Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...
View full detailsRod - Spindle Connecting
O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...
View full detailsCoolant outlet tube forming the water outlet connection at the cylinder head, in the engine cooling circuit of the 2.0L I4 AJ200 Ingenium petrol en...
View full detailsCoolant Temperature Sensor mounted in the cylinder head coolant gallery, part of the engine cooling and engine management system. The sensor is a ...
View full detailsCable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...
View full detailsExhaust Gas Pressure Sensor - measures gas pressure in the exhaust gas recirculation circuit, mounted on the right-hand side of the engine. The en...
View full detailsBolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...
View full detailsOil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...
View full detailsService PCV Kit
Bolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...
View full detailsMini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...
View full detailsO-Ring
Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...
View full detailsCoolant Bleed Hose - small-bore hose in the engine cooling system, running from the cylinder head bleed point to the coolant expansion tank. It ve...
View full detailsOil Pressure Switch from the engine lubrication system. The switch threads into an oil gallery and monitors lubricating oil pressure, signalling t...
View full detailsOil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...
View full detailsCamshaft Cover Gasket - moulded gasket sealing the camshaft cover to the cylinder head. It seals the valve train and cam carrier area against oil ...
View full detailsO-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...
View full detailsCoolant outlet tube forming the water outlet connection at the cylinder head, in the engine cooling circuit of the 2.0L I4 AJ200 Ingenium petrol en...
View full detailsValve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...
View full detailsCeramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...
View full detailsTiming Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...
View full detailsOil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...
View full detailsParts for the full Land Rover Defender range, from classic Defender 90, 110 and 130 models built between 1983 and 2016 to the new Defender L663 introduced in 2020. Genuine, OEM and aftermarket parts in EU stock. Use the collections below to shop by generation.
The Land Rover Defender name covers two distinct vehicle platforms that share a name but little else in terms of engineering, parts compatibility, or servicing requirements.
The classic Defender (1983 to 2016) was a body-on-frame utility vehicle produced in 90, 110, and 130 wheelbase variants. It ran a series of diesel and petrol engine options across its production life, from early 2.25 petrol and diesel units through the 200Tdi, 300Tdi, Td5, and the later 2.4 and 2.2 Puma TDCi engines. Parts for these models are covered in the Defender 90, 110 and 130 parts collection.
The new Defender (2020 onwards) uses a monocoque architecture on Land Rover's D7x platform, which is also used by the Range Rover L460 and Range Rover Sport L461. It is produced in 90, 110, and 130 body configurations and is offered with a range of petrol and diesel engines including the P300, P400, D200, D240, and D300 units. Parts for these models are covered in the new Defender parts collection.
Parts are not interchangeable between the two platforms. If you are unsure which generation you have, use the guidance below before adding to your basket.
Fitment NotesConfirming your generation before ordering is the most reliable way to avoid returns and delays.
The simplest check is the model year. Classic Defenders were produced from 1983 to January 2016. New Defenders entered production from September 2020. There is no Defender model year between 2016 and 2020.
For the classic Defender, the chassis number (VIN) is stamped on the chassis rail on the right-hand side of the engine bay and also appears on a plate fixed to the bulkhead. The VIN encodes body style, engine type, and build year. For the new Defender, the VIN is found on a plate in the engine bay and is also visible through the windscreen on the lower driver-side corner.
If you have your VIN, use the parts search on roverparts.eu or contact Budget Parts directly. Providing your VIN removes ambiguity from fitment, particularly for engine-dependent parts such as gaskets, filters, sensors, and drivetrain components.
Quality TiersBudget Parts stocks three quality tiers across the Defender range. Understanding the difference helps you choose the right part for your build stage, budget, and use case.
Genuine parts are manufactured by Land Rover's approved supply chain and carry Land Rover branding. They are the exact specification used in original assembly. Genuine parts are typically the highest-cost option and are best suited to vehicles being maintained to manufacturer specification, vehicles under warranty, or restorations where originality matters.
OEM parts are manufactured by the same component suppliers that produce parts for the Land Rover production line, but are sold without Land Rover branding. The component itself is often identical to the genuine part. OEM is a strong choice for mechanical replacements where factory specification is required but original branding is not.
Aftermarket parts are produced by third-party manufacturers to a compatible specification. Quality varies by manufacturer and by part type. Budget Parts selects aftermarket lines that meet the fitment and durability requirements of the application. Aftermarket is well suited to high-wear items, body components, and non-safety-critical parts where cost efficiency matters.
All three tiers are clearly labelled on every product listing.
Parts CategoriesThe Defender range is supported across all major parts categories. Both the classic and new platforms are represented, though stock depth varies by generation and component type.
Categories stocked for the Defender range include body and chassis parts, brake parts, clutch system and kits, cooling parts, driveshaft and propshaft parts, electrical parts, engine parts, exhaust parts, fuel system parts, interior parts, lighting parts, service and maintenance parts, suspension parts, and wheels and wheel parts.
For model-specific category depth, navigate into the relevant child collection first and then apply a category filter, or use the category filter on this page alongside the Defender Classic or Defender New model filter.
EU Stock and DispatchBudget Parts operates from The Hague, Netherlands, with warehouse stock available for EU-wide dispatch. Parts marked in stock are held at the warehouse and are available for same-day dispatch on orders placed before the daily cut-off. Backorder is available on parts not currently in stock, with lead times confirmed at the time of order.
Trade and workshop buyers can apply for a wholesale account through the portal linked in the site header. Volume pricing is available on high-turnover lines including filters, brake components, fasteners, and service items.
Platform designation data for the D7x architecture is consistent with Land Rover's published product and technical documentation. The Discovery 5 (L462) uses the related but distinct D7a platform and is not covered by this collection. For VIN decoding and chassis-specific parts identification, the Land Rover JTIS (Jaguar Land Rover Technical Information System) and the relevant Land Rover parts catalogue are the authoritative references.
The articles below cover Defender-specific identification, platform differences, and parts selection in more depth. Each links back to this collection for parts.
A practical Defender buying and parts guide covering TD5 injector faults, 2.4 TDCi DPF issues, brake corrosion, and L663 fitment notes. Useful for both classic and new Defender owners researching parts before purchase.
Defender parts Europe 2025 →A guide to common faults on the 300Tdi classic Defender, with diagnostic notes, the fixes that actually hold, and the proven upgrades worth doing. Useful before ordering 300Tdi engine, cooling, or service parts.
Defender 300Tdi faults →Common 2.4 TDCi Puma faults explained, including DPF blockage, EGR issues, turbo underboost, clutch failure, and MT82 gearbox problems. Covers what to check and the parts most often involved.
Defender 2.4 TDCi problems →The classic Defender (1983 to 2016) is a body-on-frame vehicle. The new Defender (2020 onwards, internal designation L663) uses a monocoque architecture on the D7x platform. The two platforms are entirely different in construction, engine family, and parts fitment. No mechanical parts are interchangeable between them. Always confirm your model year before ordering, and use your VIN to resolve any fitment uncertainty.
The easiest check is the model year. Classic Defenders were produced from 1983 to January 2016. There are no Defender models from 2017 to 2019. New Defenders entered production in 2020. If you are unsure of the year, the VIN plate on a classic Defender is located on the chassis rail in the engine bay and on the bulkhead. On the new Defender, the VIN plate is in the engine bay and is also visible through the lower driver-side corner of the windscreen.
Yes. Budget Parts stocks all three quality tiers for both the classic and new Defender where available. Genuine parts carry Land Rover branding and are built to original assembly specification. OEM parts are manufactured by the same suppliers that supply the Land Rover production line, without brand labelling. Aftermarket parts are third-party components selected for fitment compatibility. Each listing on roverparts.eu clearly identifies which tier the part belongs to.
Yes. Budget Parts dispatches EU-wide from its warehouse in The Hague. Delivery is available across all EU member states. Shipping costs and estimated delivery times are shown at checkout based on your delivery address. Parts marked in stock are available for same-day dispatch on orders placed before the daily cut-off.
Yes. Budget Parts operates a wholesale portal for trade buyers, workshops, and resellers. You can register through the wholesale portal linked at the top of the site. Trade accounts provide access to volume pricing on high-turnover lines including service items, brake components, filters, fasteners, and drivetrain parts. There are no minimum order requirements to open an account.