Price <10

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Hose Clip is a worm-drive band clamp used to secure flexible rubber hoses onto rigid pipe spigots and unions across the coolant, heater, fuel and i...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Bumper Mounting Bobbin is a mounting bobbin for the front bumper. It sits between the bumper and its mounting bracket, locating the front bumper a...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Flanged Bolt secures the steering damper bush at the steering damper mounting. The flange spreads the clamp load across the bush, retaining the da...

Wiper Spindle Washer for the rear screen wiper assembly. This plastic outer washer fits over the wiper spindle where it exits the body panel, seati...

Wiper Motor Grommet for the rear screen wiper assembly. It seals the aperture in the rear door or tailgate where the wiper motor spindle passes thr...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Rocker Shaft Spring for the Rover V8 valvetrain, fitted on the rocker shaft assembly. The spring acts as a spacer between adjacent rocker arms, ho...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Relay - normally open 4-pin relay for use in the underbonnet fuse and relay box. In its de-energised state the load contacts are open; energising t...

High/Low Gear Retaining Nut for the LT230 transfer box. This nut secures the high/low range gear on the transfer box mainshaft, holding it against...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Blanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Plastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Wheel Nut - replacement nut for the Terrafirma RVS alloy wheel, supplied as a set of 5. These nuts clamp the wheel to the hub. A set of 5 provides...

Wheel Nut - black-finish replacement nut for the Terrafirma RVS alloy wheel. Clamps the wheel to the hub; the black finish matches the matt-black ...

Oil pump relief valve washer V8

Track Rod Clamp secures the adjustable joint of the steering track rod. Fitted around the split end of the rod, it pinches the threaded sleeve clos...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Blanking Plug Fills the headlamp washer jet aperture in the front bumper on vehicles not fitted with headlamp washers. It presses into the moulded ...

HT Lead for V8 petrol engines, part of the high-tension ignition circuit. The high-tension lead carries the ignition output to the spark plug. Sup...

Injector O-Ring is the small-diameter sealing ring for the fuel injector on V8 EFi petrol engines. It seals the lower end of the injector at its s...

Automatic Transmission Sump Plug - Magnetic for the automatic gearbox valve block. This drain plug fits the automatic transmission sump and incorp...

Blanking Plug for the front bumper assembly. Closes an unused aperture at the centre of the front bumper. Black.

Handbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...

Flywheel Bolt for the Td5 2.5L 5-cylinder turbo diesel with automatic transmission. It secures the drive plate to the rear flange of the crankshaft...

Body Mounting is a rubber isolator in the body-to-chassis mounting system. It sits between the body and the chassis frame, cushioning the body aga...

Bulb and holder GENUINE LR - D2 instrument panel - main beam

Timing Pin (Short) is a workshop special tool used to set the engine timing on the Td5 2.5-litre five-cylinder turbo diesel. The pin locates throu...