Price <10

Decal - Diesel Adhesive fuel-type identification label for the fuel filler. Applied at the fuel filler flap or filler neck to identify the vehicle...

Parking Distance Control Bezel - the trim bezel that locates a parking distance control sensor within the rear bumper. It holds the ultrasonic sen...

Touch-Up Paint Stick in Zambesi Silver. The stick applies a small quantity of colour-matched paint to stone chips and minor scratches, restoring t...

Drive Plate Screw is a threaded fastener used in the V8 automatic transmission drive assembly. It retains the drive plate (flexplate) to the crank...

Hose Bracket - a retaining clip for the heater pipe and hose. It secures the heater hose along its run, holding it in position and preventing chaf...

Valve Guide for the V8 petrol engine, fitted in the cylinder head as part of the valvetrain. The guide is pressed into the head and supports the v...

Woodruff Key for the V8 petrol engine. A semicircular (half-moon) key that seats in a shaft keyway to angularly locate and lock a mating gear, pull...

Fender Seal - a seal fitted along the fender (wing) to close the gap against the adjacent body panel, helping to keep out water and road debris.

Sealing Washer forms the fuel-tight seal for the water-in-fuel sensor where it threads into the Td5 fuel filter housing, within the fuel filtration...

Clip - retaining clip for the door latch and lock mechanism. Secures the operating linkage within the door latch and locking assembly, holding the...

Washer A washer used in bolted and screwed fixings to spread the clamping load over the joint face and to protect the surface as the fastener is ti...

Stud - Cylinder Head & Front Cover - Td5 2.5L five-cylinder turbo diesel. Fixing stud used at the cylinder head and front cover joint, at the ...

50A Fuse is a circuit-protection device fitted in the under-bonnet fuse box. Rated at 50 amps, it protects its associated circuit by interrupting ...

Insert

Headlamp Trim Screw for the front lighting assembly, M6 x 12 mm. The screw secures the top trim of the headlamp to the surrounding front body panel.

Vacuum Hose Assembly for the turbocharger wastegate control. It carries vacuum to the wastegate actuator, regulating boost pressure on the turbocha...

Nut M14 x 1.5 - M14 fine-thread hex nut (1.5 mm pitch). Used in axle and suspension assemblies where fine thread engagement provides greater clamp...

Body Mount Washer is a load-spreading washer used at the body-to-chassis mountings. It sits under the body mount fixing to distribute the clamp lo...

Synchromesh Plate for the R380 5-speed manual gearbox. The plate forms part of a synchroniser hub assembly within the main gear cluster. It acts o...

Forming Thread Screw is an M6 thread-forming screw. As it is driven into an unthreaded pilot hole, it displaces material to form a matching female...

Monobolt Rivet - 1/4" structural blind rivet for body and chassis fastening. The Monobolt is a high-strength blind rivet set from one side of the ...

Air Cleaner Mounting Rubber for the engine air intake system. This flexible rubber mount locates and supports the air cleaner (air filter) housing...

Fuel Filler Caution Label for the fuel filler. This adhesive label is fitted at the filler neck and carries the fuelling caution notice for the cu...

Handbrake Adjusting Knob threaded adjuster fitted to the parking brake (handbrake) lever assembly. The knob threads onto the end of the handbrake ...

Dowel for the manual gearbox gear-selector assembly. It locates the selector components against the housing to hold their alignment during gear eng...

Clamp steering column

Hex Nut is an M16 hexagonal fastening nut used to secure threaded studs and bolts in body, chassis and running-gear assemblies.