Price <10

Interior Trim Retainer Clip - a moulded fastener used to secure interior trim to the vehicle body. The clip retains door casings, pillar trims and...

Hex Nut - M14 for use in Land Rover suspension and general fastener applications. A metric M14 standard hexagonal nut for use in axle, suspension,...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Wiper Arm Pivot Nut Secures the wiper arm to the splined pivot spindle of the windscreen wiper mechanism. It threads onto the spindle where it emer...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Fuel Leak Off O-Ring seals the leak-off (spill return) connection at a diesel fuel injector. It sits in the injector leak-off circuit that collect...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Brake Drum Clip is a retaining clip within the rear drum-in-hat parking brake (handbrake) assembly. It secures the handbrake shoe against the back...

Gearbox Sump Gasket for the automatic transmission oil pan. This is the gasket only - it seals the oil pan and oil screen to the gearbox case. For...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Circlip for the lower steering knuckle bush. This circlip retains the bush within the lower steering knuckle, forming part of the front axle and s...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Intercooler to Inlet Manifold Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit on the Discovery 1 and Range Rover Classic. ...

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Exhaust Gasket - downpipe joint gasket sealing the connection between the exhaust downpipe and the intermediate pipe section. Fits across several ...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Screw - M5 x 20 mm fixing screw used to secure the front and rear wheel arch mouldings and the adjoining rear bumper section to the bodywork. A bo...

Bolt for the rear suspension assembly. This fastener is used in the rear cross member and stabilizer bar assembly, and in the rear knuckle and low...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Pollen Filter for the cabin ventilation system, installed in the HVAC air intake housing. It traps pollen, dust and airborne particulates from the...

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Oil Drain Plug for the ZF transfer box housing. The plug closes the drain and fill port in the transfer box casing, and is removed to drain and re...

Bolt - M6 x 35 - a threaded fastener with a 6 mm metric thread and a 35 mm length. Used to clamp and secure components together at points where th...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Tow Hook Protective Cap is a cover for the towing eye aperture in the bumper. It closes off the tow hook mounting point when not in use, keeping o...

Fuel Filler Door Seal is the rubber seal fitted around the fuel filler door aperture in the rear body panel. It seals the recess behind the hinged...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Wheel Nut finished in black, used to secure the Terrafirma TF152-series 18x8 modular steel road wheel to the hub. Supplied in a black finish to ma...

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...