Price <10

Bolt for the upper front suspension arm. This fastener secures the upper front suspension arm within the front axle and suspension assembly.

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Trim Clip - retaining clip for interior trim panels. Secures interior trim components such as the instrument panel, glove box and speaker surround...

Washer used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Thermostat Housing Gasket in the engine cooling system. This 37 mm gasket seals the joint between the thermostat housing and the engine on AJ-V8 4...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Asy Lamp

Washer - Sealing

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Flywheel Bolt with hex head, securing the flywheel to the crankshaft rear flange on the 2.7L V6 Lion turbo diesel fitted with the ZF S6-53 six-spee...

Inlet Manifold Seal for the 4.4L AJ V8 petrol engine, sealing the lower inlet manifold to the cylinder head within the air induction system. It cl...

Rear moulding cap - exterior body trim. The cap closes off the moulding at the junction between the rear bumper and the rear wheelarch moulding, c...

Transmission Oil Drain Plug for the ZF 6HP26 and 6HP28 six-speed automatic transmission - Transmission External Components assembly group. M18 x 1...

Amber Bulb - 12V 5W wedge-base (W5W) bulb with an amber envelope, used in the exterior lighting circuit. It serves the direction indicator functio...

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

Nut for the diesel fuel injection pump and timing gear. Secures the drive gear to the high-pressure fuel injection pump on the 2.7L Lion V6 diesel...

O Ring

Trim Clip retains interior trim panels against the body. The clip pushes into a pre-formed aperture in the body panel and holds the trim in place ...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Screw - a general fixing screw used at several mounting points across the driveline and body, including transmission and transfer case mountings, t...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Blind Anchor Nut - a threaded anchor nut that provides a captive fixing point where the reverse side of the panel is inaccessible. It is used in t...

Connecting Rod Bolt for the connecting rod assembly of the TDV6 / TDV8 turbo diesel V-engine. The bolt clamps the big-end cap to the connecting ro...

Brake Pipe Connector - a junction fitting in the hydraulic brake circuit that joins rigid brake pipes. It provides a sealed connection between bra...

Tailgate Pivot for the rear tailgate (luggage compartment door). This pivot forms the hinge point about which the upper tailgate swings, locating ...

Bolt - M10 x 140 for the brake and clutch control assembly. Hexagon-head threaded fastener, M10 x 140 mm, used in the pedal box and clutch/brake c...

Blind Nutsert is an M6 blind rivet nut (rivnut) that provides a captive threaded fixing point. It is set into a single face of sheet metal or pane...

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Front Brake Caliper Spring - the anti-rattle retaining spring for the front brake caliper. The spring holds the brake pads located in the caliper,...