Range Rover Sport L320 Parts

Door Trim Name Plate - decorative name plate fitted to the visible face of the inner door trim panel. A cosmetic trim item only; it carries no str...

Primary Drive Belt - the main accessory drive belt of the 5.0L supercharged V8 petrol engine, running from the crankshaft pulley around the front-e...

Parking Brake Cable Bracket from the parking brake cable routing. The bracket anchors the cable outer casing at a fixed point on the vehicle, so th...

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...

Self-Tapping Screw - a fastener that cuts its own thread as it is driven, used in the luggage compartment door finisher and trim assembly. It secu...

O-Ring for the engine cooling system - it seals the water outlet tube at its connection to the cylinder block, alongside the thermostat housing. T...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Camshaft Cover Gasket - LH seals the left-hand camshaft cover to the cylinder head on the AJ133 5.0L V8 petrol engine. It closes the joint around ...

Accessory Drive Belt - ribbed serpentine belt for the front-end accessory drive of the 5.0L naturally aspirated V8 petrol engine. Driven from the ...

Idler Pulley for the front auxiliary drive belt on the 2.7 and 3.0 V6 diesel engines, part of the pulleys and drive belts assembly at the front of ...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Oil cooler seal, 9.5 mm diameter, sealing the small-bore oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diese...

Idler Pulley for the primary accessory drive of the 5.0L V8 petrol engine (AJ133). It is a free-running, non-tensioning pulley that routes and sup...

Exhaust Manifold Gasket - right-hand side seals the exhaust manifold against the cylinder head face on the right-hand bank of the engine. It conta...

Tube - Drain

Thermostat for the engine cooling circuit of the 2.7 V6 Lion turbo diesel, supplied as the thermostat and water outlet connection assembly. The th...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Timing Chain Tensioner Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing c...

Exhaust Manifold Gasket seals the exhaust manifold to the turbocharger on the 3.0L V6 diesel engine. Fitted at the manifold-to-turbocharger flange...

Water Outlet Tube carries engine coolant within the cooling circuit of the 5.0L V8 petrol engine (AJ133). It runs from the thermostat housing to t...

Cable

Collet - Anti-Roll Bar Pipe - retaining collet used in the pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The co...

O-Ring sealing the thermostat housing in the engine cooling circuit. Seats between the thermostat housing and its mating face to seal the coolant ...

Turbocharger Oil Return Tube Gasket seals the oil return (drain) tube where it meets the turbocharger, within the turbocharger lubrication circuit....

Brake Pipe for the rear hydraulic braking circuit, right-hand side. This rigid, pre-formed pipe carries pressurised brake fluid along the vehicle ...

Brake Pipe for the rear hydraulic circuit, left-hand side, part of the braking system. This is the rigid metal pipe (brake tube) that carries brake...

Crankshaft Seal and Retainer - the rear crankshaft oil seal complete with its retainer housing, sealing the rear of the crankshaft where it exits t...

EGR Gasket Inlet

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Brake Pad Fitting Kit

Rear Brake Pad Fitting Kit - the retaining clip set for the rear brake pads. The kit supplies the clips that locate and retain the pads within the...

Front Brake Caliper Spring - the anti-rattle retaining spring for the front brake caliper. The spring holds the brake pads located in the caliper,...

Washer and Screw - a screw supplied together with its washer as a single fastener assembly. This is a multi-purpose fixing used at a range of body...

Brake Pad Fitting Kit

Breather Valve for the axle case or manual transmission housing. The valve vents the housing to atmosphere, allowing internal air pressure to equa...

Number Plate Bracket for the rear of the vehicle, mounting the registration plate to the luggage compartment door (tailgate). The bracket holds th...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Disc - Brake - Vented

Coolant Overflow Hose connects the cooling system to the expansion (overflow) tank. Fitted to the 5.0 litre supercharged V8 petrol engine (AJ133),...