Genuine Land Rover Parts

Locknut is a 1/4" UNF self-locking nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibrati...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Screw - No.10 x 1" Pan head, self-tapping, pointed fastener used in door trim and window regulator assemblies. It secures the interior grab handle...

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Rocker Shaft Locating Bolt for the 2.25L and 2.5L petrol, 2.5L naturally aspirated diesel and 2.5L turbo diesel engines, securing the rocker shaft ...

Wiper Switch Assembly

Door Speaker An original-fit speaker for the in-car audio system. It reproduces the audio output of the radio/head unit through the vehicle's spea...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Locking Wheel Nut for replacing one standard wheel nut per wheel as a theft deterrent. The locking wheel nut features a unique external drive prof...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Steering Hose forms part of the power steering hydraulic circuit. It carries pressurised hydraulic fluid between the power steering pump and the s...

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

Packing Strip fitted between the bulkhead base and the footrest bracket mounting on the chassis of Defender 90/110. This strip provides the correc...

Exhaust U-Bolt secures a joint in the front section of the exhaust system. The U-bolt clamps over the pipe at a slip joint and, tightened against i...

Heater Hose - a coolant hose in the heater circuit, connecting the heater to the engine pipework. It carries engine coolant to and from the heater...

Decal is an exterior body decal applied to the rear of the vehicle. It carries the Land Rover name in silver lettering on a black background, and ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Cigar Lighter Mounting Plate, the fascia panel that carries the cigar lighter unit. It mounts into the dashboard fascia, locating and retaining th...

Nut Plate for the rear side door and sill panel assemblies. It provides captive threaded anchor points for the door hinge and check strap fixings,...

Windscreen Glazing Seal - the moulded rubber seal that mounts the windscreen glass into the front bulkhead aperture. It locates and cushions the gl...

Heater Controls Spacer - spacer fitted within the heater control assembly of the HVAC unit. Sold individually.

Bonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...

Intercooler to Turbocharger Hose is part of the charge-air (boost) system. It carries pressurised air between the turbocharger and the intercooler...

Name Plate is the front 'DEFE' lettering decal in black, forming the first half of the DEFENDER name applied to the exterior. It pairs with the 'N...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Clevis pin

Plate

Front Seat Belt Assembly for the Defender occupant restraint system. This complete front seat belt assembly includes the belt, retractor, and buck...

Oil Filter Gasket for the four-cylinder 2.25L/2.5L petrol and 2.5L naturally aspirated diesel engines, part of the engine lubrication circuit. The...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Cylinder Liner - the replaceable liner that forms the bore in which the piston and rings run within the cylinder block. It provides the hard weari...

Pedal Clutch Bearing

Protect your Defender 90 (FA>WA) with this Genuine LR Rear Mudflap Assembly for the left-hand side (LHS). This mudflap is black and includes a b...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Cab Mounting Stud

Distance piece