Genuine Land Rover Parts

Gear Lever Assembly for the LT95 4-speed gearbox. The main gear-change lever the driver operates to select gears. It mounts to the gearbox and act...

Terminal Bush and Lead for the ignition distributor low-tension (primary) circuit. The insulated terminal bush carries the low-tension feed throug...

Ventilator Filler Piece

Sill Finisher Spacer packs out the interior sill finisher, part of the door sill trim and tread plate assembly. The spacer sits behind the sill fi...

Facia Mat is the padded covering that fits over the upper surface of the dashboard, forming the finished top face of the facia. It sits along the ...

Bonnet Hinge assembly for the bonnet and locking platform. Provides the pivoting attachment between the bonnet and the front body, allowing the bo...

Bonnet Striker Pin for the bonnet release and latch assembly. This pin engages with the bonnet catch to secure the bonnet in the closed position on...

Shim Washer used in the steering box assembly to adjust end-float and pre-load during overhaul or reassembly. Fits the recirculating-ball steering ...

Nut for securing the side repeater lamp lenses to the body on the Defender and Range Rover Classic. Four nuts are required per vehicle. This nut i...

Door Hinge Assembly mounts a side door to the body and allows it to pivot open and closed. The assembly bolts between the body pillar and the door...

Steering Column Shroud Spacer fitted within the steering column shroud assembly. The spacer sets the correct clearance and positions the shroud ar...

Check Strap is a front door mechanism that controls how far the door opens. Mounted between the door and the body pillar, it limits the door's swi...

Door Lock & Handle Retaining Clip - securing clip within the exterior door handle and lock assembly. This clip retains the door lock and handl...

Front Door Seal for the front door aperture. The rubber weatherseal that fits around the front door opening, sealing against wind, water and road ...

Coolant Hose connecting the engine to the heater control valve. Part of the heater coolant circuit, it carries hot coolant from the engine to the ...

Rear Bumper Over Rider - right-hand end cap for the rear bumper assembly. This moulded rubber over rider fits to the outer end of the rear bumper,...

Bumper Over Rider is a protective end cap that mounts on the rear bumper. It caps the end of the bumper and provides a raised contact face that ab...

Lamp Grommet is a rubber grommet fitted at the side and flasher (front indicator) lamp mounting. It seals the aperture where the lamp wiring passe...

Tailgate Lock Lid Cover is a trim cover panel fitted over the lock aperture on the upper section of the tailgate. It conceals and protects the tai...

Tailgate Lock Lid Cover is a trim cover panel fitted over the lock aperture on the upper section of the tailgate. It conceals and protects the tai...

Seat Belt Bolt Cap is a trim cover that fits over the head of a seat belt anchor bolt. It conceals the mounting bolt at a seat belt anchorage poin...

Bolt for the outer body panels, securing the wheelarch and front valance to the vehicle body. A hex-head setscrew used as a body-panel fixing, cla...

ATF Cooler Pipe Clip for the automatic transmission oil cooler circuit. The clip secures the automatic transmission fluid (ATF) cooler pipe, holdi...

Main Bearing Cap Bolt for the cylinder block bottom end, clamping a main bearing cap to the block and retaining the crankshaft main bearing shells....

Coolant Feed Pipe - Turbocharger carries engine coolant from the cooling circuit to the turbocharger, forming part of the turbocharger water-coolin...

Screw - M4 x 16mm metric machine screw used as a general fixing. A multi-application fastener rather than a component-specific part; the same scre...

Spring Nut is a sheet-metal fastener used in body panel and interior trim assemblies. It clips over a panel edge or into a pre-formed hole to prov...

Rear Parcel Shelf Support Bracket supports the rear parcel shelf in the loadspace, providing the mounting point that carries and locates the shelf....

Strap assy Door Channel MWC2486

Piston Assembly for the 3.5-litre Rover V8 petrol engine, supplied at 0.020" oversize for a rebored cylinder block. It locates in the cylinder bore...

Coolant Hose to Turbocharger for the 2.5L 4-cylinder VM turbo diesel engine. This hose carries engine coolant to the turbocharger, feeding the wat...

Layshaft Roll Pin for the manual transmission. This roll (tension) pin locates and retains the layshaft within the gearbox casing, holding the sha...