Genuine Land Rover Parts

Key Blank for Land Rover lock barrel assemblies. This uncut key blank matches the barrel profile used in door locks, ignition locks, the tailgate, ...

Splined End

Cable

Injector Bush for the VM 2.4L and 2.5L 4-cylinder turbo diesel engine in the Range Rover Classic. This bush is fitted at the cylinder head to loca...

Rear Door Glass for the right-hand rear door. This is the main window pane that raises and lowers within the door. It is guided by the glass run c...

Rear Side Door Glass for the left-hand rear side door. This is the main window pane that raises and lowers within the door. It is guided by the gl...

Rear Upper Tailgate Handle, the exterior handle assembly for the upper section of the split rear tailgate. It provides the grip and release point ...

Switch - Window Lift - Centre Console - Discovery 1/RRC

Fan Motor for the in-dash air conditioning condenser and receiver-drier assembly. The motor drives the fan that draws air across the condenser and...

Upper Clutch Pipe is the rigid metal section of the hydraulic clutch actuation circuit running from the clutch master cylinder. It carries fluid f...

GENUINE LR camshaft sprocket for Rover V8 engines

4-Pin Differential for the Land Rover-type axle. The differential takes drive from the propshaft through the crown wheel and pinion and splits it ...

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Rear View Mirror

Shim 1.65mm for Layshaft Speed - V8 4

Throttle Disc is the throttle butterfly for the Solex carburettor, operating in the air and fuel induction system. Mounted on the throttle spindle...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Body Side Panel is the right-hand rear outer bodyside panel, part of the Bodyside Outer Panels assembly. It forms the external sheet-metal skin ov...

SRS ECU - the Supplemental Restraint System electronic control unit, commonly known as the air bag control module. It sits at the centre of the SR...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Shim bearing differential 0.062""

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Locking Wheel Nut Kit for alloy road wheels, part of the road wheel and fixings assembly. Each locking nut replaces a standard wheel nut at one pos...

Seal

Split Pin used throughout the handbrake and gearchange linkages. The pin passes through a clevis pin or castle nut and its legs are spread on asse...

Collet - air suspension pipe connector. The collet is the gripping ring inside a push-fit air line fitting. Its internal teeth bite into the outer...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Kit - Caliper Brake Pad

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Turbocharger Adaptor Pipe in the induction system of the 2.5L 200 TDi and 300 TDi turbo diesel engines. It forms the connecting pipe between the t...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Cable Clip for securing and routing cables and wiring to body and chassis structures.

Restrictor - flat 20 mm plain washer used in the suspension link mountings of the coil-sprung live-axle chassis. It is fitted at the radius arm mo...

Wire - Ignition

Lamp

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Engine Mounting Bracket - 3.5L V8

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Cooling Fan for the front-end cooling pack on vehicles built with factory air conditioning. The fan draws air through the condenser and radiator a...