Land Rover Defender Parts

Front Crankshaft Oil Seal for the Ingenium engine family, sealing the crankshaft nose where it passes through the front cover. The seal runs on th...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Timing Gear Special Nut from the front timing gear assembly, securing the lower primary timing chain guide. The nut locates and clamps the guide a...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Coolant Temperature Sensor mounted in the cylinder head coolant gallery, part of the engine cooling and engine management system. The sensor is a ...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Mini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Oil Pressure Switch from the engine lubrication system. The switch threads into an oil gallery and monitors lubricating oil pressure, signalling t...

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Ceramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Timing Gear Bolt - a fixing bolt in the engine timing drive, retaining a timing gear. It secures the timing gear on the 2.0L four-cylinder AJ200 p...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Cup Holder - an interior trim component fitted to the floor (centre) console. It provides a moulded holder to retain cups or containers within the...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

TMAP Sensor is the combined intake air temperature and manifold absolute pressure sensor, fitted to the inlet manifold and intercooler ducting. It...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Bolt for the drive belt and pulley assembly on the AJ200 / AJ20 engine family. This fixing secures a pulley or tensioner component at the front of...

Rear Crankshaft Oil Seal for the 2.0L AJ200 engine. This seal fits around the rear of the crankshaft where it exits the cylinder block, retaining ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit, 60mm. This seal maintains a gas-tight joint within the EGR section, sealing the connection...