Land Rover Freelander Parts

Wiper Motor Rack for the front windscreen wash/wipe system, for left-hand drive applications. The rack transfers drive from the wiper motor to the...

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Sump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Exhaust Gasket - Catalyst - sealing gasket for the catalytic converter joint in the Freelander 1 exhaust system, suitable for both petrol and diese...

Valve Collet for the K Series and KV6 petrol engine cylinder heads. The tapered collet locks the valve spring retainer to the valve stem, holding ...

Heater Resistor Pack for the heating and ventilation (HVAC) blower circuit. It provides the stepped resistance that sets the lower blower motor fan...

Drive Shaft - Front transmitting torque from the front differential to the wheel hub. The VIN break to (V)YA999999 distinguishes this shaft from t...

Head Gasket - 1.8L - Metal is the cylinder head gasket for the 1.8L Rover K-Series petrol engine used in the Freelander 1. This multi-layer steel ...

Timing Belt Tensioner for 1.8L K-Series petrol engines built without automatic belt tensioning. Mounts in the timing belt run and applies the work...

Timing Belt for the Freelander 1 1.8L petrol engine. This 143-tooth toothed rubber belt drives the camshaft from the crankshaft, maintaining valve...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Mirror Glass - LH is the replacement glass element for the left-hand exterior door mirror on the Freelander 1. It fits non-powerfold mirror assemb...

Fitment: All 2.0L L Series diesel models

Wheel Hub Bearing for the front and rear wheel hub assemblies. The bearing locates the hub on the stub axle and steering knuckle, carrying the veh...

Wheel Centre Trim Cover for steel road wheels. This black plastic cap fits into the centre of each steel road wheel, covering the wheel fixings an...

Air cleaner filter element

Screw for use in Land Rover body, chassis, and hardware applications.

Fuel pressure regulator BMW Diesel OEM BOSCH

Changeover Relay

Fuel Filter - Freelander TD4

Exhaust Tailpipe for the 2.0-litre Td4 diesel engine, forming the rear section of the exhaust system. It connects to the rear silencer outlet and ...

Intermediate Exhaust Pipe for the Freelander 1 1.8L petrol engine (from VIN 1A000001). This pipe forms the middle section of the exhaust system, c...

Hill Descent Control Switch - push-push switch mounted in the clutch (bell) housing, forming part of the Hill Descent Control input circuit. The s...

Viscous Coupling for the rear propshaft drivetrain, for 4-cylinder petrol and diesel applications (not fitted to V6 models). The viscous coupling ...

Clutch cylinder hydraulic assy Freelander OEM

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Radiator Hose - Top - upper radiator hose in the engine cooling circuit of the 1.8L K16 16-valve petrol engine. It carries hot coolant from the en...

Crankshaft Oil Seal (rear) seals the rear of the crankshaft where it leaves the cylinder block into the bellhousing, retaining oil in the crankcase...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Cylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...

Bulb Holder Assembly - Clock & Cigar Lighter

Relay - Normally Open is a plug-in make-contact relay used in the vehicle fuse and relay panel. The relay closes its high-current main contacts on...

Fastener - Interior Trim is a fir-tree type push-in fastener used to retain interior trim and soft furnishing components to the body panels. The r...

Heavy-duty winter wiper blades, supplied as a front pair. The blade frame is enclosed in a protective cover so that snow, ice and slush cannot pac...

Parking Aid Sensor - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the bumper cover. The transducer emits a...

Stop and Tail Bulb - 12V 21/5W twin-filament bulb. Two filaments share a single envelope: the 21W filament serves the stop lamp and the 5W filamen...

W5W Capless Bulb - 12V 5W wedge-base bulb. The W2.1x9.5d capless base pushes straight into the lampholder, the bulb's own wire leads folded back a...

H7 Halogen Bulb - 12V 55W headlamp bulb. H7 is a single-filament halogen capsule on a PX26d base, serving the dipped or main beam function dependi...

H7 Halogen Bulb - Twin Pack - 12V 55W headlamp bulbs, supplied as a pair. H7 is a single-filament halogen capsule on a PX26d base, serving the dip...

Propshaft Bolt securing the propshaft flange to the viscous coupling unit (VCU) in the driveline. It clamps the flange faces together so drive tor...

Sealing Washer for the transfer box casing plugs, fitting both the drain plug and the filler/level plug. It seats between the plug head and the ca...

Rear Lamp Seal - left-hand foam gasket sealing the rear lamp assembly against the body panel. It sits between the lamp housing flange and the body...

Transfer box drain and filler plug - the combined drain, filler and level plug in the transfer box casing. Screws into the casing to seal the oil ...

Differential Oil Seal for the final drive of the Jatco five-speed automatic transmission. It seals the differential output where the driveshaft pa...

Rear Lamp Assembly - Stop & Flasher - rear lamp cluster within the rear exterior lighting assembly group, combining the stop lamp and direction...