Price <10

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Front Bumper Tapping Plate fitted behind the front bumper mounting points, providing a reinforced steel backing surface for the bumper fixing bolts...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Nyloc Nut with a 5/8" UNF thread, used as a self-locking fastener in the suspension linkage. The nylon insert deforms around the bolt thread on as...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Spring Washer, 5/16" nominal size. A split helical washer fitted under a nut or bolt head as a fastening hardware component. The sprung split appl...

Door Lock Button Escutcheon is the interior trim surround that frames the sill-mounted door lock button where it passes through the door casing. I...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Copper Sealing Washer for the oil drain plug of the LT77 and R380 manual gearboxes. The washer forms a leak-free seal between the drain plug and t...

Transfer Box Sump Gasket for the LT76 combined gearbox and transfer box unit used in Series Land Rovers. This flat sealing washer seals the transf...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Pipe clutch down

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Bonnet Buffer for the Land Rover bonnet assembly. This rubber buffer mounts to the body structure and provides a cushioned contact point for the u...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Salisbury Joint Washer for the Salisbury rear axle differential. The gasket seats between the differential carrier and the axle casing, sealing th...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Axle casing oil seal

Interior Lamp Lens for the centre interior lamp mounted in the headlining. The lens is the translucent cover that locates over the centre courtesy...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Stub Axle Oil Seal - Inner

Oil Filter Housing Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the oil filter housing/adaptor to the cylinder block. It sea...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Diesel Fuel Filter - Inline for the 2.5L TDi and Td5 2.5L 5-Cylinder diesel fuel system. Fitted at the sedimentor position in the fuel supply line...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...