Range Rover Evoque L538 Parts

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Upper Radiator Hose for the engine cooling circuit on the 2.0L Ti VCT petrol engine. This upper radiator hose carries engine coolant from the engi...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Oil Sealing Ring - Haldex - With Nut is the input flange sealing ring and retaining nut for the Haldex rear differential coupling unit. The sealin...

Latch hood, bonnet, RH and LH, with sensor

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Sump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...

O-Ring - Haldex to Rear Differential seals the joint between the Haldex coupling and the rear differential in the all-wheel-drive driveline. The 1...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Oil Filter Adaptor for the rear-drive Haldex coupling (Active On-Demand Coupling) in the all-wheel-drive driveline. The filter keeps the oil in th...

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Cylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Exhaust Manifold Fixing Spacer - a fixing component within the exhaust manifold mounting arrangement of the 2.2L CR DI 16V four-cylinder diesel eng...

Iridium Spark Plug for the 2.0L 16V TIVCT turbocharged petrol engine (Si4, 240PS). The plug threads into the cylinder head and fires beneath its c...

Rear Crankshaft Oil Seal and Retainer forms the oil-tight closure at the flywheel end of the cylinder block, within the Cylinder Block and Cranksha...

Inlet valve stem seal for the cylinder head valve train. The seal is pressed onto the inlet valve guide boss and wipes the valve stem as it recipr...

Rear Crankshaft Oil Seal and Retainer forms the oil-tight closure at the flywheel end of the cylinder block, within the Cylinder Block and Cranksha...

Inlet valve stem seal for the cylinder head valve train. The seal is pressed onto the inlet valve guide boss and wipes the valve stem as it recipr...

Valve Stem Seal, Exhaust - cylinder head valve train of the 2.0L 16-valve TiVCT turbocharged petrol engine. Fits over the exhaust valve stem at th...

Valve Stem Seal, Exhaust - cylinder head valve train of the 2.0L 16-valve TiVCT turbocharged petrol engine. Fits over the exhaust valve stem at th...

Oil Filter for the engine lubrication system. Filters contaminants from the engine oil, protecting the lubrication circuit. Fitted to the 2.0L 16V...

Water Pump Pulley for the 2.0L 16V TIVCT turbocharged petrol engine. It mounts to the water pump drive and is turned by the auxiliary drive belt, t...

Front Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...

Front Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...

Front Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...

Front Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...

Pinion Bearing Spacer sits within the rear axle differential, setting the spacing and preload of the pinion bearings on the drive pinion. It maint...

Crankshaft Sprocket is the timing gear mounted on the nose of the crankshaft. Fitted to the 2.0L 16-valve turbocharged petrol engine, it drives th...

Crankshaft Gear forms part of the timing gear train, mounted on the crankshaft nose to drive the timing system and maintain synchronisation between...

Cylinder Head Bolt clamps the cylinder head to the engine block, within the cylinder head assembly. It holds the head against the block and head g...

Shock Absorber Boot for the suspension damper assembly. The boot sheaths the exposed damper piston rod, shielding it from grit, moisture and road ...

Shock Absorber Boot for the suspension damper assembly. The boot sheaths the exposed damper piston rod, shielding it from grit, moisture and road ...

Cylinder Head Cover Gasket for the 2.0L Petrol engine. This gasket seals the cylinder head cover to the cylinder head, containing oil within the v...

Cylinder Head Cover Gasket for the 2.0L Petrol engine. This gasket seals the cylinder head cover to the cylinder head, containing oil within the v...

Screw - M6 x 25mm threaded fastener used across the 2.0L Ingenium petrol engine assembly. Secures components at the timing gear, fuel injector, wa...

Coolant Hose for the engine cooling circuit of the 2.0L 16V turbocharged petrol engine. It carries coolant between the cooling system components, f...

Coolant Hose for the engine cooling system on the 2.0L 16V TiVCT turbocharged Petrol. This hose carries coolant within the cooling circuit, connec...

Pollen Filter for the heater and ventilation assembly. This cabin air filter installs within the heater assembly, filtering the air drawn into the...