Allmakes4x4 Parts

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Cigar Lighter Assembly - facia-mounted 12V cigar lighter, comprising the socket body and the heating element that seats in it. The element is push...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Alternator – 300TDi The engine-driven charging unit that powers the electrical system and maintains battery charge on the 2.5L 300 Tdi diesel engin...

Low Note Horn is the low-pitched unit of the audible warning system, mounted behind the front grille or bumper. It sounds together with the high n...

High Note Horn - the higher-pitched element of the dual-tone warning horn assembly. Mounted behind the front grille or valance and paired with a l...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

High Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...

Stop Lamp Cover for the high-level (high-mounted) centre stop lamp. This cover forms the outer lens of the high-mounted stop lamp assembly at the ...

Front Left-Hand Indicator Lamp Assembly for the Discovery 1. This amber turn signal lamp unit is mounted at the front left corner of the vehicle a...

Kit gasket carb for Rover V8 engines fitted with SU carburetors

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Wheel Bearing Kit - Front and Rear

Wheel Bearing Kit - Front and Rear

Wheel Bearing Kit - Front and Rear

Wheel Bearing Kit - Front and Rear

Plain Washer - Swivel Pin Housing is a flat washer used within the front axle swivel pin housing assembly. It seats beneath the housing fixing bolt...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Washer - 20mm

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Drain plug

Intermediate shaft lock nut LT230

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Oil Cooler Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, carrying fluid between the gearbox and the transmission oil coo...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Input shaft for the R380 five-speed manual gearbox. Carries drive from the clutch into the gearbox: the splined nose engages the clutch driven pla...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Dowel, used with 3-bolt flange. (For Hardy coupling)

Front Axle CV Joint, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft and transmits ...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Hex Bolt, grade 8.8, M8 x 20mm. A standard metric hexagon head bolt. Grade 8.8 indicates a tensile strength of 800 MPa and a yield strength of 640...

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Piston Ring Set - 0.020in Oversize - 300TDi

Kit latch bonnet catch LHD

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...