Allmakes4x4 Parts

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Number Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It sits in the rear number plate surround an...

Exhaust System Screw, M8 x 20 mm. Used on exhaust and turbocharger joints - securing the catalytic converter to its mating pipe section, and at tu...

Exhaust System Bolt, M8 x 45 mm. Used at the catalytic converter flange joint, clamping the converter to its mating exhaust pipe section. Fastene...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Tow Bar Electrics - 12N/12S for the towing electrical circuit, supplied as a wiring harness terminating in twin 7-pin sockets. The 12N (normal) so...

Transmission Oil Cooler in the automatic gearbox cooling circuit. Automatic transmission fluid is routed out of the gearbox and through the cooler...

Transmission Sleeve for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It is fitted within the main control valve body, where it forms th...

Gear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...

Differential Seal for the front axle. This O-ring seals the joint between the front differential case and the drive shaft support (extension) tube,...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Sump Screw for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It retains the transmission sump pan against the gearbox casing, clamping ...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Torx Bolt - M12 x 25 mm used to secure the rear propshaft flange connections on Discovery 3, Discovery 4, Discovery 5, Range Rover L405, Range Rove...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...

Transmission oil drain plug for the ZF 6HP six-speed automatic gearbox, sealing the drain aperture in the transmission fluid pan. The plug is remo...

Brake Caliper Screw for the front brake caliper and parking brake installation. Retains the caliper or its carrier to the mounting face on the hub...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Caliper Bolt for the front brake caliper assembly. This bolt secures the brake caliper to the hub carrier. It is a critical fastener in the front ...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Brake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly. The carrier bolts to the rear hub carrier and holds t...

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...

Parking Brake Cable Clip - retaining clip from the parking brake cable installation. The clip secures the parking brake cable outer sheath to its ...

Parking Brake Cable Bracket for the left-hand side of the parking brake actuation circuit. The bracket secures the parking brake cable to the rear...

RH bracket for fitting parking brake cable to suspension arm

Rear Brake Wear Sensor is part of the rear braking assembly, fitted to the brake pad on the rear axle. The sensor monitors brake pad thickness. As...

Rear Brake Wear Sensor is part of the rear braking assembly, fitted to the brake pad on the rear axle. The sensor monitors brake pad thickness. As...

Grommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Service Kit - 5.0 V8 Petrol

The OEM Service Kit for Discovery 4 (3.0 V6 Diesel with DPF) and Range Rover Sport (3.0 V6 Diesel with DPF) is a comprehensive, high-quality servic...

Service Filter Kit - a combined filter kit for a major scheduled service of the 2.7L TDV6 diesel engine. It brings together the routine service fi...

Brake Pedal Pad for automatic transmission applications - the moulded rubber cover that fits over the brake pedal lever in the pedal box assembly. ...

Handbrake Shoe Fitting Kit

Brake Pad Wear Sensor - front brake pad wear warning wire, part of the front disc brake friction-monitoring circuit. The sensor wire clips into th...

Front Brake Pad Fitting Kit - pad guide pin and boot set for the front brake caliper. The guide pins pass through the caliper and locate the brake...

Coated Brake Disc is a rear brake rotor for the rear-axle braking assembly, finished with a protective coating on its non-friction surfaces. The d...

Brake Disc - a front vented brake disc with a protective coating, the rotating friction surface the caliper pads clamp against to slow the vehicle....

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Bolt for the rear suspension. It secures the lower mounting of the rear shock absorber to the lower suspension arm, carrying the damper load as the...

Bolt for the upper front suspension arm. This fastener secures the upper front suspension arm within the front axle and suspension assembly.

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...