Allmakes4x4 Parts

Protect the load area of your Range Rover Sport (2005-2013) with this high-quality rubber replacement mat. Designed to fit perfectly into your vehi...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

ACE Seal Kit for the Active Cornering Enhancement valve block. The ACE system operates hydraulic actuators on the front and rear anti-roll bars to...

Filter valve assy

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Auxiliary Drive Belt for the 2.7L TDV6 diesel engine on vehicles without an active roll stabiliser, 2092mm. This ribbed belt transmits drive from ...

Belt Tensioner Kit - 2.7 TDV6

Hose Intercooler - TDV6

Expansion Tank Cap

Nut - Flag Type

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Water Connection for the turbocharger coolant feed, lower position, in the turbocharger lubrication and cooling circuit of the 3.0L AJ20P6 Ingenium...

Crankcase Breather Cover - part of the crankcase ventilation assembly on the 3.0L Ingenium AJ20P6 six-cylinder petrol engine. The cover closes the...

Aluminium Intake Manifold

Crankcase cover gasket for the crankcase ventilation (emission control) cover on the 3.0L Ingenium six-cylinder petrol engine - AJ20P6 / AJ22P6, in...

Spark Plug - ignition spark plug for Ingenium petrol engines (AJ20 / AJ22 series, including PHEV applications). The plug screws into the cylinder ...

Blind Rivet Pin is a plastic blind-rivet fastener, 9.4 mm head diameter by 13 mm long. It secures trim panels, covers and liners by expanding to g...

Tyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...

Screw - threaded fastener used in body and chassis assembly.

O-Ring

Brake pad wear sensor for the rear brakes, forming part of the brake pad wear warning circuit. The sensor is a wire loop carried in a moulded body...

Brake pad wear sensor for the rear brakes, forming part of the brake pad wear warning circuit. The sensor is a wire loop carried in a moulded body...

Front Brake Pad Wear Sensor, part of the front brake pad and caliper assembly. The sensor is a sacrificial wire loop held in a moulded carrier tha...

Front Brake Pad Wear Sensor, part of the front brake pad and caliper assembly. The sensor is a sacrificial wire loop held in a moulded carrier tha...

Air Filter is the engine intake air filter element, carried in the air cleaner housing upstream of the turbocharger inlet. It traps dust, grit and...

Ceramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Alternator Assembly

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Bus voorste draagarm

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Pump Water 3.0d

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Power Steering Pump for the 2.7 V6 Lion and 3.0L V6 turbo diesel engines, forming the pressure source of the hydraulic power steering circuit. Dri...