Allmakes4x4 Parts

Tow Bar Electrics Kit - 12N & 12S 7-Pin is the twin 7-pin trailer socket installation for the towing electrical circuit. The 12N socket carrie...

Door Switch Assembly - driver's door switch pack for the front door trim casing, combining the electric window lift rockers with the exterior mirro...

Height Sensor Jumper Lead for the electronic air suspension system. This connecting lead links a ride-height sensor to the chassis wiring harness,...

Parking Sensor for the Park Distance Control (PDC) system. This ultrasonic sensor fits into the bumper and transmits and receives ultrasonic pulses...

Parking Aid Sensor for the front bumper inner position, forming part of the Parking Distance Control (PDC) system. The sensor emits ultrasonic pul...

Parking Aid Sensor, Rear - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the rear bumper cover. This is the ...

Halogen Bulb, H8 - 12V 35W single-filament halogen capsule for the exterior lighting system. The H8 uses the PGJ19-1 base and is the 35W member of...

Front Fog Lamp Bulb - H11 halogen capsule rated 12V 55W, operating in the exterior lighting system. The H11 uses the standardised PGJ19-2 base, wh...

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Number Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It sits in the rear number plate surround an...

Front Fog Lamp - Right-Hand for the front bumper lighting assembly. This lamp mounts in the front bumper fog lamp aperture and provides supplement...

Flanged Nut, M8. The integral flange spreads clamp load across the joint face and removes the need for a separate washer. Used in the exhaust syst...

Exhaust System Bolt, M8 x 45 mm. Used at the catalytic converter flange joint, clamping the converter to its mating exhaust pipe section. Fastene...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Module

In-Tank Fuel Pump for the 2.7L V6 and 3.6L V8 diesel fuel delivery system, in the configuration used on vehicles equipped with a fuel-fired heater....

Fuel Pump Module is the in-tank unit that draws fuel from the tank and delivers it under pressure to the engine fuel rail. The module carries the ...

Fuel Pump Module is the in-tank unit that draws fuel from the tank and delivers it under pressure to the engine fuel rail. The module carries the ...

Fuel Sender Cover - the tank-top closure over the fuel sender aperture, incorporating the in-tank fuel filter, part of the fuel tank sender and mou...

Catalytic Converter for the 2.7L TDV6 turbo diesel engine. Positioned downstream of the exhaust manifold, the catalytic converter reduces harmful e...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Transmission Sleeve for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It is fitted within the main control valve body, where it forms th...

Gear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...

Differential Seal for the front axle. This O-ring seals the joint between the front differential case and the drive shaft support (extension) tube,...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Sump Screw for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It retains the transmission sump pan against the gearbox casing, clamping ...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Torx Bolt - M12 x 25 mm used to secure the rear propshaft flange connections on Discovery 3, Discovery 4, Discovery 5, Range Rover L405, Range Rove...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...

Transmission oil drain plug for the ZF 6HP six-speed automatic gearbox, sealing the drain aperture in the transmission fluid pan. The plug is remo...

Brake Caliper Screw for the front brake caliper and parking brake installation. Retains the caliper or its carrier to the mounting face on the hub...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Brake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly, dimensioned for the rear disc size used with the 18-in...

Brake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly. The carrier bolts to the rear hub carrier and holds t...

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...

Parking Brake Cable Clip - retaining clip from the parking brake cable installation. The clip secures the parking brake cable outer sheath to its ...

Parking Brake Cable Bracket for the left-hand side of the parking brake actuation circuit. The bracket secures the parking brake cable to the rear...

RH bracket for fitting parking brake cable to suspension arm

Rear Brake Wear Sensor is part of the rear braking assembly, fitted to the brake pad on the rear axle. The sensor monitors brake pad thickness. As...

Rear Brake Wear Sensor is part of the rear braking assembly, fitted to the brake pad on the rear axle. The sensor monitors brake pad thickness. As...

Grommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Service Filter Kit - a combined filter kit for a major scheduled service of the 2.7L TDV6 diesel engine. It brings together the routine service fi...