Range Rover Evoque L551 Parts

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Fuel Filler Cap for unleaded petrol applications, sealing the fuel tank filler neck. The cap closes the filler neck and keeps the tank sealed agai...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Drive Shaft Boot Kit - Outer Constant Velocity Joint - Front, part of the front axle drive shaft assembly. The boot seals the outer constant veloc...

Drive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...

Engine Mounting Bolt, M14 x 65mm, used in the engine mounting assembly. The bolt secures the engine mounting to its bracket. It carries the static...

O-Ring for the high-pressure diesel fuel injection pump. The ring seals the joint between the pump body and its mounting face on the engine, preve...

DEF Injector Refit Kit

Ball Stud - Tailgate Strut - the ball pivot that a tailgate (luggage compartment door) gas strut socket clips onto. It threads into the body apert...

Front Crankshaft Oil Seal for the Ingenium engine family, sealing the crankshaft nose where it passes through the front cover. The seal runs on th...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Anti-Roll Bar Link - Front, the connecting link between the front anti-roll bar end and the suspension strut in the front suspension assembly. The...

Front Brake Pad Wear Sensor for the front axle brake assembly, part of the brake pad wear warning circuit. The sensor consists of a wire loop seat...

Front Brake Pad Wear Sensor for the front axle brake assembly, forming part of the brake pad wear warning circuit. The sensor is a wire loop carri...

Coolant Temperature Sensor mounted in the cylinder head coolant gallery, part of the engine cooling and engine management system. The sensor is a ...

Rear Shock Absorber - hydraulic damper for the rear suspension, fitted between the body mounting point and the rear suspension arm. The damper con...

Glow Plug - the pre-heat element for one cylinder of the 2.0L four-cylinder AJ200 / AJ20D4 diesel engine, threaded into the cylinder head so its ti...

Oil Pressure Switch from the engine lubrication system. The switch threads into an oil gallery and monitors lubricating oil pressure, signalling t...

Screw - threaded fastener used in body and chassis assembly.

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Rear shock absorber for the rear suspension assembly, for applications without adaptive damping. The damper controls oscillation of the rear sprin...

Drive Belt for the belt-driven starter generator (BSG) drive at the front of the engine. The belt transmits torque between the crankshaft pulley a...

Ceramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...

Cabin Pollen Filter, 272x195x43mm - the filter element in the HVAC intake housing, installed upstream of the blower motor and evaporator. All air ...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

Glow Plug - the pre-heat element for one cylinder of the 2.0L four-cylinder AJ200 / AJ20D4 diesel engine, threaded into the cylinder head so its ti...

Exhaust Gas Pressure Sensor for the diesel exhaust aftertreatment system. The sensor is connected by take-off pipes to the exhaust upstream and do...

Cabin Pollen Filter, 272x195x43mm - the filter element in the HVAC intake housing, installed upstream of the blower motor and evaporator. All air ...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

TMAP Sensor is the combined intake air temperature and manifold absolute pressure sensor, fitted to the inlet manifold and intercooler ducting. It...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

Fuse installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when the rated c...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...