Allmakes4x4 Parts

Kit - Arm with Bolts RRS 10-13

Rear Lower Suspension Arm Kit - LH

Rear Lower Suspension Arm Kit - RH - the right-hand rear lower control arm (wishbone) supplied with its mounting nuts and bolts, for vehicles with ...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Water Inlet Tube in the engine cooling system, forming a rigid section of the coolant circuit on the inlet side. Fitted to supercharged petrol eng...

Coolant Hose carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It runs f...

Thermostat Hose - coolant hose serving the thermostat housing. Carries engine coolant between the thermostat housing and the cooling circuit as pa...

Thermostat Hose - coolant hose serving the thermostat housing. Carries engine coolant between the thermostat housing and the cooling circuit as pa...

Tailgate Latch is the locking latch for the tailgate, part of the tailgate and luggage compartment lock controls. It engages the striker on the bo...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Symposer intake sound resonator for the 5.0L supercharged V8 petrol engine (AJ133). The symposer draws pressure pulses from the inlet manifold and...

Windscreen Washer Jet for the front screen-wash system. It mounts to the bonnet and directs washer fluid from the pump feed onto the windscreen. T...

Transfer Case for the four-wheel-drive driveline, mounted to the rear of the gearbox where it distributes drive between the front and rear propshaf...

Transfer Case for the four-wheel-drive driveline, mounted to the rear of the gearbox where it distributes drive between the front and rear propshaf...

Rear Brake Backplate is the left-hand plate that mounts to the rear axle and carries the parking-brake shoe assembly behind the rear brake disc. I...

Heated Windscreen Washer Jet delivers washer fluid onto the front windscreen to clear road film and maintain driver visibility. The jet incorporat...

Water Outlet Connection sits at the engine coolant outlet within the cooling circuit, directing coolant from the engine into the connected hoses an...

A-Pillar Finisher - exterior trim finisher fitted to the left-hand A-pillar (windscreen pillar), covering the join between the windscreen surround ...

Gasket - Throttle

Brake Calliper for the front axle, right-hand side, part of the front disc brake assembly. The calliper houses the hydraulic pistons and clamps th...

Brake Caliper for the front left-hand position, supplied without brake pads. The caliper houses the hydraulic pistons that clamp the brake pads ag...

A-Pillar Finisher - outer exterior trim for the right-hand A-pillar, finished in satin black. The finisher covers the outer face of the A-pillar b...

Rear wheel bearing kit contains the wheel bearing, circlip and new hub nut.

Fuel Filter Head is the housing top of the fuel filter assembly within the diesel fuel supply system, onto which the filter element mounts. The he...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Air Suspension Compressor Cover - Upper is the upper half of the protective housing that encloses the air suspension compressor. It shields the co...

Air Suspension Compressor Cover - Lower is the lower half of the protective housing that encloses the air suspension compressor. It shields the co...

Fuel Sender Flange for the fuel tank pump, sender and filler assembly. This flange seats over the fuel level sender and pump aperture on top of the...

Fuel Pump Module is the in-tank electric fuel pump and level sender assembly that delivers pressurised fuel to the engine. Fitted to petrol applic...

Oil Filter and Cooler is a combined assembly within the engine lubrication circuit, integrating the oil filter housing with the engine oil cooler. ...

Rear Towing Hook that fits the rear tow hitch receiver, providing a rated attachment point for towing and recovery at the rear of the vehicle. Sup...

Exhaust Crossover Pipe carries exhaust gas between the two cylinder banks of the 3.0 V6 diesel engine, routing the outlet of one manifold across th...

EGR Outlet Gasket seals the outlet joint of the exhaust gas recirculation (EGR) assembly. Fitted to the 3.0L V6 diesel (TDV6) engine, it forms a g...

Parking Aid Sensor is an ultrasonic Park Distance Control (PDC) sensor mounted in the bumper. It emits and receives ultrasonic pulses to measure t...

Crankshaft Rear Seal and Retainer - the rear main oil seal and its housing, part of the cylinder block and plugs assembly at the rear of the cranks...

Crankshaft Timing Trigger Wheel for V6 and V8 diesel engines. The toothed reluctor wheel mounts on the crankshaft and passes the crankshaft positi...

Secondary Drive Belt Idler guides and maintains tension on the secondary (supercharger) drive belt within the front-end accessory drive. The idler...

Fan Bracket for the 5.0L V8 petrol engine (AJ133), supplied complete with idler pulley. The bracket mounts to the front of the engine and carries ...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Drive Belt Tensioner - maintains correct tension on the front accessory (auxiliary) drive belt. The sprung tensioner assembly applies constant loa...

Inlet Manifold Gasket for the right-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifol...

O-Ring for the variable valve timing (VVT) solenoid. Seals the VVT solenoid where it locates into the cylinder head, retaining oil pressure to the...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Fuel Injector Pipe Clamp for the high-pressure fuel injection system of the 3.0L V6 and 4.4L V8 (SDV8) diesel engines. The clamp secures a high-pr...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...