Allmakes4x4 Parts

Shackle plate

Wheel Brace for loosening and tightening road wheel nuts. It has a 15/16 in AF (approximately 24mm) hexagon socket, sized for the wheel nuts fitted...

Lower Steering Drop Arm for the steering relay assembly. This is the lower lever that clamps to the bottom of the steering relay shaft. Within the...

Thermostat for the engine cooling circuit, controlling coolant flow between the engine and radiator. The valve stays shut while the engine warms f...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Upgrade and restore the swivel housing assembly on your Land Rover Series 2 with this swivel pin conversion kit. Designed for improved durability a...

Waterpump pulley

Layshaft (countershaft) for the manual gearbox, specific to the Suffix B and C gearbox builds. The layshaft carries the constant-mesh cluster gear...

lock washer. sold EACH.

Thermostat Gasket for the thermostat housing on the 2.25L petrol engine. This paper gasket seals the thermostat housing to the cylinder head, prev...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Grab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...

Washer used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Rear left-hand leaf spring designed for short wheelbase Land Rover Series vehicles. This road spring is configured with 11 leaves and is intended ...

Road Spring SWB Rear 11L

Exhaust Front Pipe for the 2.25L petrol engine, forming the first section of the exhaust system between the manifold and the intermediate pipe. It...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Locking plate

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Tappet kit

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Lock Nut, 5/16 BSF, a self-locking nut used on the transmission parking-brake assembly. It retains the transmission (handbrake) brake drum, its se...

Headlamp Bulb - 12V 40/45W Non-Halogen - LHD

In/out member spring

Exhaust Connecting Pipe is the intermediate section of the exhaust system, linking the front downpipe to the rear silencer assembly in the Series E...

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Door Seal A general-purpose door aperture weather seal, suited to the front doors, rear side doors and rear door/tailgate openings. It seals the g...

Door Seal The lower rear door seal for the left-hand front door, sealing the lower rear edge of the door against the body. It forms part of the fr...

Door Seal The lower front door seal for the left-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the l...

Door Seal The lower front door seal for the left-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the l...

Door Seal The lower front door seal for the right-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the ...

Lower Door Panel forms the bottom half of the two-piece door assembly, for the Left Hand (LH) side. It is the lower structural panel of the door b...

Door Bottom - RH is the lower repair section of the right-hand front door. It replaces the corroded or damaged bottom portion of the door frame, r...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...